Keith W. did a "It's November and you want to do a show" video. I'm not where I can find it right now, but if you do a search for it, there are a LOT of good pointers in it for someone starting late in the season.
Sure, your deadline is what you want it to be, and not anybody else; and besides, it's a permanent house outline. I just know it's easy to confuse 12/25 as your self-imposed deadline for whatever you want for this Christmas, when it's really more like Thanksgiving weekend or the week after. It's a permanent outline, and this Christmas is an important milestone. I was just outside all morning setting up pixels for this Halloween, and it's barely past Labor Day; and I've done this before. I have a goal of October 1st for 80% of it. And then I have a transition plan on to Thanksgiving, and on to Christmas. If I had a target date of October 22nd, it's like you do all that work for just one week of lights.
I agree with some of the same thing's folks are saying here, but I know my first year, I started my setup in late September, my show that first year was a mess in my opinion (no leds, renard 110v only w/112 channels), I had power issues, replaced breakers, network issues, audio issues, we didn't even have xLights back then, but it was so much fun, and I learned a lot. If it's not perfect, people will still come and love it.
As to your power injection, I run my show at 30% power except for Dec 24th, 25th and 31st. I tried to have reduced power injections in the past and it's just not worth the effort you will sink so much time into troubleshooting things that don't even look like power issues. Power inject at least every ~150+/- nodes if you ever plan on 100% power, always plan for 100% and you will have a lot less issues to troubleshoot. Once you get your bearings, you can mix it up and try to push some boundaries.
As for the universes, that is really based on controllers you own and the port setup each provides. I have one controller that can only support 512 channels for just 1 universe and another that supports 510 channels per universe with up to 12 universes. I also have others that can support much more and support both 512 and 510 channels per universe. So, however you lay it out, just make sure it makes sense to you and how you use them in xLights. BTW, that is where all your time will be spent in order to get your show going if that is the software you decide to use. Even if you purchase some prebuilt songs, you have to build your layout in the application you will use and then create or import each song. If you have not started that yet, your very far behind.
Thanks for all the great info. I?m definitely not planning any songs for this year. I?ll be happy if I can get steady orange for Halloween. I?ve been busy prepping all of my pixels for my house outline in my Pixel Track, I haven?t had time to even understand the hardware and software wide of things.
I have a layout built in X lights, but that?s as far as I?ve gotten. I know I need multiple controllers, and already have the power supplies, but have no idea what exactly the pi?s do. There will be a steep learning curve and I?m not sure I?ll have it fully understood in time; or ever.
I think your power injection plan is fine. You have 12 volt pixels. They are not subject to the fade out that 5 volt pixels do. I have 4 Sans controllers with 3 near maxed out and several strands that on the roofline 300 pixels long with no power injection. The only issues I had was long runs from the controller to the the roof pixels. I had to add signal regenerators every 10 feet to keep the last few feet pixels from losing signals. As far as Wifi, I only use it to communicate to the Falcon PI. All controllers talk to the Falcon via ethernet. Not as clean yes, but so much faster and room to expand.
One thing to think about on the Wifi vs. cable is, I am pleased thus far using Wifi mesh range extenders. It's harder to figure out network-wise than just to use a dedicated show router, but my property has solid Wifi now, and I can optionally configure my virtual show network to see the outside internet if i want it to. The range extenders come with ethernet jacks, so if my controllers require a physical ethernet connection, they need route only to the nearest extender (which in turn talks wirelessly to the main router). The wireless connections on the Christmas controllers themselves can be flaky, but I tend to trust the extenders. The one thing I haven't done is really stress my network with 30,000 pixels on FPP remote, even as teenagers are streaming television and playing games, and/or with my ISP provider down (which SHOULD not matter...). The networks may be virtually different, but they still are sharing some of the same hardware.
You could theoretically use extenders to extend a separate show router, too, but you would lose the benefit of those providing your property a solid Wifi for regular internet use. (what I figure is, if you're going to blanket your property with lights, then why not blanket your property with good Wifi, too, and solve two problems at once)
