Hey guys, my inquiry is general in nature right now. I want to see who has these, and the failure rates they are seeing. I am seeing about 6-7% failure rate. I bought 60 strings of 42ct pixels. I have been chasing failures left and right. I know some have gotten them in group buys, some on their own. There have been about 3K of these strings made in 3 batches I am told. I am interested in how many are being used in our decorating community.
Right now I have no good strategy on repair, because some strings are not so straight forward in troubleshooting.
Mark, What type of failures are you seeing? Are they failing on the bench or when the go outdoors?
John
ughhh. have tested my lines like 5 times...go to do one final check tonight and get everything hooked to the computer and controllers set...tc pixels going out. CRAP..replaced one...have three more out. looks like if you watch them the offending pixel will go blank...then the ones after flicker....was up on the roof fixing second pixel...looked over and frost was forming on the roof.....TIME TO COME DOWN
I'm under the assumption my "FirePix" I got through Holiday Coro are the same things. I'm certainly experiencing the same issues. I tested many times. Didn't even move them from "the bench" (my media room), then all of a sudden I went to test again, and poof, pixels have gone bad causing the string to go white. Against my better judgement, I picked the 24 best strings that didn't exhibit any issues. Not sure if it was today's rains, but they had been working great all week. Just went out to give them a test run before tomorrow's go live, and you guessed it, 3 or 4 strings are now Joseph's Amazing Technicolor Dreamcoat the moment they're powered. These are on my 45 foot palm trees, so there's really no way I have right now to replace them other than paying the landscapers to bring out a boom truck. I spent days carefully zip tying these to lengths of vinyl coated steel cable to make sure they're supported. I'm crossing my finger's that tomorrow some miracle happens and they work again, but not counting on it. I knew I should have backed them up with good old incandescents. I had already replaced/cut out probably 24 - 32 offending pixels only to have another on the string go bad. My only hope is that David will make good when I finally bring these down in January. As they die, I'm just going to be unplugging them from the controllers. I'm sure they're going to look real sad come Christmas day.
I bought 42 - 50 count strings. Failures in at least half of them. Expecting more.
I am having the same issues node failures here and there. This was from a batch that was shipped in October. I put up the 3 strings I brought in July and are testing them now. The spacing on the nodes was different from the first batch and the last batch. I just hope it is the later batches.
Turn your P/S down some. Say to 10V. I am even running at 9.75V and enough power is there to not have loss at the end of the string. The 2811 only needs 5V. Ray designed a LDO voltage regulator to step the voltages down and if they are driven by a full 12V, they overheat, and shorten the life.
zman wrote:Turn your P/S down some. Say to 10V. I am even running at 9.75V and enough power is there to not have loss at the end of the string. The 2811 only needs 5V. Ray designed a LDO voltage regulator to step the voltages down and if they are driven by a full 12V, they overheat, and shorten the life.
So, what you're saying is we should have just made 10 the loudest? Thanks.. I've cranked all of mine down to 10. Let's see if this keeps down further failures. Two of the offending strings are front and center. Had to disconnect both because off was better than on. I may try pulling out the ladder tomorrow and trying an in-place patch of one string. I think the ladder will just barely reach to the offending pixel.
And in theory, this means that anyone who bought 5V strings wouldn't be having the issue. Can anyone confirm that?
I think I got mine down to 11.25...i have some fairly long injections so by the time it reaches the injection point I probably have a fair amount of voltage loss. I have been chasing pixels all morning. replaced 8-10 and its' clearing up. I replaced a few pixels that were DEAD...which makes all pixels after it SOMETIMES flicker, but mostly they turn white. Those are easy to identify. However, I have replaced some that were flickering and I try to follow the pixels up to where they stop flickering. Based on what I've replaced with those...its the one BEFORE the flickering starts...I was HOPING based on what timon said I had a chance of sidestepping some of the problems....if this keeps up it's going to be a long December. In addition to being upset as I have worked HARD like most of us do at setting this up and getting stuff on the roof and windows...I now REGRET putting the TC's on the roof line...I should have opted to put those on the windows...it would have been easier to get to and fix....sitting here debating if I should at least get the front peak redone with some of the 2801s and just chase the tc's down on the roof line...I have to work tonight and will chase some down later this evening at 10 o'clock..not supposed to be as cold tonight...My priorities are
1. Get all sequences corrected with universes and pixels...you'd think this would be easier..
2. Test my show with everything BUT the technicolor pixels.
3. Take a look at technicolor pixels to see if I think I can chase the issue down. If its not done by this evening...tomorrow FIRST THING I will be on the peak with a ladder...rented a lift this year for this...and at LEAST get pixels on the front peak...maybe won't look as bad...my show starts at 6 tomorrow..have about 60 people coming over at 5
Thats my plan...looks to be a LONG NIGHT!
MindTrik wrote:Thats my plan...looks to be a LONG NIGHT!
Good luck! I'm rooting for you. I've disconnected four strings on my trees. Going live tonight. We'll see who notices the big blank spots.
Isn't this where the Christmas miracle is supposed to happen?
Good Luck MindTrik! I am not even planning on going live until middle of the week now. Took down all TC strings the other night an have been replacing my roof grid. Trying to get it done before the "Arctic Storm" hits us on Monday. Highs on Wednesday supposed to be 25. I have a lot to do on my roof tomorrow! :disgust:
