Technicolor quality...
 
Notifications
Clear all

Technicolor quality?

256 Posts
45 Users
0 Reactions
83.4 K Views
bdeditch
Posts: 82
(@bdeditch)
Estimable Member
Joined: 19 years ago
MindTrik wrote:From what I understand in conversations with not just Zack, its the voltage regulator. It was suggested by one to dial down the PS to around 10V to help the regulator out. I can say I am NOT happy not being told, it not being listed that these are in fact 5V strings with a regulator...I might would have passed. .. Zack isn't really responsible for the internals of this, I don't think he controls that. Also, I don't see any posts on FB where people are talking about failures...In addition, I think he feels there might have been a manufacturer change..so this would only effect recent pixels. I have some 2801s that are from last year that only have the water ingress issue.

Chances are he deleted those posts.


Reply
Posts: 214
(@gary-martin)
Estimable Member
Joined: 18 years ago

FB posts, Mark Zembruski in the Extreme Pixels and LEDs forum:

Hey guys, in a rush so just posting without looking deeply, sorry. Technicolor pixels, E682, Meanwell 350W P/S. I am having single pixels work, then not work. On the tree it shows problems. Pull it down to remove the pixel and it works. Put it back on the tree and after a while it is out again.

There are other random issues. Pixel completely dead, that is a replacement. But there are sections where it is color above a section, all white and then again color below the white section.

In Seattle so the temps are cold enough to just keep the P/S's dialed to 11.75V.

Input? I have my electrical Guru here with me today, Pete Peters lending a hand getting the Pixel Tree worked on. Thanks.

Roger DeBolt who has about 3,500 Technicolor pixels and a very large portion are failing:

http://doityourselfchristmas.com/forums/showthread.php?29390-Technicolor-Pixels&p=296435#post296435

Steven Singleton Jr. in the Extreme Pixels and LEDs FB group:

Question for any of you all but when I went to hook up the technicolor pixels on the outside of the house the strands there are just not taking any commands. I am using the 6804 and also a e682. When I tell them what to do a few will respond but for the most part they just are white. What could be giving me the issues? Is it a data issue? Is it some sort or moisture issue? Is it reversible or do I have 4 strands of technicolor pixels that will not be able to be used?

Those are just a few that came up easily. FB is such a P.I.T.A. to search for anything on. Someone needs to build a better social site.


Reply
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago

From what I have seen SO FAR...white was when there was a signal problem, but power on the line...rainbow was when there was signal, but not enough power....again..THAT'S SO FAR. SO FAR, I have had 4 pixels go out that caused what issues I've had. This is out of about 475. I am NOT using the covers, however, a friend of mine is and he has had about the same number of pixels go out with about the same number total on the roof.


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

I think that most of us like the basic design of the Technicolor pixels. The interchangeable covers, easy mounting and the ability to run over a wide voltage range are great design features. It does look like there is a design issue that needs to be looked into.

First I don't see any problem having a local regulator in the pixels as it actually helps the pixels operate over a wider voltage range. However if it's not done correctly it can be a failure point.

Same for the case, you have to cover the issue of water migration and how to make sure if some water does get past the wire to case or LED to case it won't cause a failure.

I all deference to Zack I'm already talking to Ray about working with him to not only get to the bottom of the problems but to go over design changes to solve any problems we find. This will include not only logic changes but any case changes as well.

This testing will start once I get my display running so I figure around the middle of next December. I'll be performing some tests on the current logic board and I'll be asking Ray to make some specials pixels just for testing. These tests will likely result in some design changes to the TC pixels.

This is going to be a total design review and I will report back my results. Nothing will be hidden, if I find issues I'll report them to the forum.

When this is complete I'll ask Ray to supply some complete strings for testing by some forum members.

Finally, once this is completed I'm asking Ray to supply the pixels in not only the current black but green and white as well.

I'm doing ths at no charge to Ray and to help the community.


Reply
bcwhitehead
Posts: 119
(@bcwhitehead)
Estimable Member
Joined: 15 years ago

Hey Timon Thanks of the support on these. I have 50 stings of 50. I haven't had them all on and won't this year due to my mom being sick. I would be more then willing to donate one string for your testing and disection since I don't need it this year. Pm me your address and I will send one your way. I received these in August of this year. Let me know.

Brandon


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

Thanks for the offer and if needed I'll take you up on that.

Did you get them when they had the group buy or did you order them direct from Ray?


Reply
Steven010
Posts: 416
(@steven010)
Honorable Member
Joined: 18 years ago

Hey guys, just jumping in here to mudddy waters, I read breifly through this, maybe someone already tried this, can anyone connect a single string to a bench power supply, or simply have a good DMM, set up to measure current, turn on a single color on a single bulb, measure current, step through colors on single bulb, measure for each color? Maybe try more than first pixel, check two or three?

I bet red draws more current, I be red goes out first...any takers?

I suspect that everyone may have "walking wounded" parts at this point, they may be all junk, just matter of time. Also, may be able to salvage the season simply by dropping voltage driving the strings. A say simply, it may not be very simple for everyone...


Reply
bcwhitehead
Posts: 119
(@bcwhitehead)
Estimable Member
Joined: 15 years ago

Timon, I got them from Ray. I was not part of the group by.


Reply
Posts: 154
 zman
(@zman)
Estimable Member
Joined: 18 years ago

Guys are these the 12VDC version? If so send me an IM or email. I too am seen very high failure rates, and I am gathering in for Ray Wu,Thanks.


Reply
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago

Zman...group buy or direct? Also how many pixels have you lost and the total you started with..just curious


Reply
Page 6 / 26
Share: