Technicolor quality...
 
Notifications
Clear all

Technicolor quality?

256 Posts
45 Users
0 Reactions
83.4 K Views
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

Is it known that the pixabulbs use constant current direct drive from the 2811? If so one would indeed expect 18.5ma/color.

But of course the 2811 can also be used in constant voltage mode with external transistors, and let you pick the current you want; if the Pixabulbs are designed in this way then that could explain any apparent discrepancy.

And yes, running at lower current as described would make each LED dimmer; however since you are getting two 5050's in series for the same current, that would compensate, allowing you to get a similar light output (more or less...) with lower current from the power supply.


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

Actually you don't need external transistors just put resistors in series with the LEDs. The ws2811 output will try to limit to 18.5 am and lock down hard so the resistors will then set the current.

The when this is done your basically turning a WS2811 into a TM1804.


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

Speaking of the power dissipated in the controller chip, I like this (google translation of a) segment of the TM1829 spec sheet:

"The greater the reduction in power consumption chip, the chip severe fever, reducing overall system reliability."

Or in real English : "the more power you dissipate in the chip, the hotter it will be, reducing overall system reliablity". But I kind of like "the chip severe fever".


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

So that's the problem, the chips need an antibiotic for there fever:biggrin:


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago
timon wrote:Actually you don't need external transistors just put resistors in series with the LEDs. The ws2811 output will try to limit to 18.5 am and lock down hard so the resistors will then set the current.

The when this is done your basically turning a WS2811 into a TM1804.

I wondered about that but did not find anything like that in the datasheet.

As I understand it, the WS2811 in direct drive (constant current) mode should attempt to keep the current through each color line at 18.5 mA, whether the LEDs are powered at 5, 12, or 24 V; whether there is 1, 3 or 6 LEDS in series; and whether or not there is series resistance. Of course the word here is "attempt" - it can only do that within certain ranges (and there will be "chip severe fever" if you try to dissipate too much power).

So what I gather is that you could insert a large enough series resistor such that the WS2811 would saturate, driving as hard as it can, and not be able to pull the full current. For example if you had a 3.3V LED on 12V with a 870 ohm series resistor dropping the other 8.7v, you could not draw any more than 10ma even if the chip's Vout at 10 mA was 0.0v. Adjust for an actual desired current and the real Vout at that current and pick a standard resistor size for each color. It's no longer constant current nor constant voltage, it's mostly just an LED and a resistor, so the current is going to vary considerably with power supply voltage at the pixel. Right?

This makes the most sense in speculating on the Pixabulb, especially since there are only two LEDs in series at 12V so you would probably need series resistors even if you wanted 18.5V to reduce the chip's fever (see the resistor on OUTR in the datasheet, since three red LED's don't drop enough voltage). So just raise the series resistance until you drop the current to where you want it (at the cost of no regulation).


Reply
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago

Just got off the roof. I tested all the pixels I had on the roof last week and they all lit up. Spent most of today on a lift putting lights on my peaks . Hooked everything up and about 60 pixels in I lost my string. Replaced that pixel and I have another just before the last string starts. So I will be sending you a few pixels next week. I also have one that flickers blue when all lights are off, but responds when its told to change color.. Will send that one too. Hopefully this isn't the start of a habit..


Reply
dsmjuggalo
Posts: 663
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

Had another bulb today "lose" it's color. It responds fine when told what to do but the red is more of a pink, but stays blue when not getting a signal. Also had the last 6 bulbs of a window frame go black. That makes 9 technicolor failures and 0 pixabulb failures...


Reply
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago

Dsm..if the last six went out..most likely its ONE pixel thats the issue..hard to say if it's the last one lit not sending signal or the first one out thats not receiving. ..


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

Yeah, seems like it could be useful to have a test LED with insulation piercing clips for debugging, to help figure out where the signal (or power) stops working well...


Reply
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago

If I'm in a hurry, I just cut the first effected pixel out and the one before it...and quick splice two new ones in and test the ones I removed at the bench, toss the bad one and place the good one in drawer. Not that I have many...just what I've been doing. I have a short 24" piece of 4 core with alligator clips to do a quick test.


Reply
Page 5 / 26
Share: