timon wrote:BTW, I'm going to talk to some of the injection plastics manufactures, once my show is running, about different plastics and how they adhere to different wire insulations and the resins use for the LEDs. I'm really to the point that I think if there is a water ingress issue with the TCs its due to the plastic body not molding tightly adhering to the wires.
I thought Zach had considered all this when he did the design... Very disappointed.
My pixels are not Technicolor, I just want everyone to be aware of that, just normal 2811 bullet nodes. The symptoms are exactly the same though. There are several other people with the same symptoms but the pixel types are different. I didnt want to hijack this thread since it is about technicolor.
timon wrote:Id like to understand the layout.
- Looks like 29 strings of 50 pixels each.
- Custom built or standard lengths?
- Which controller and how many? (E681, E682, E6804 or J1Sys)
- How long of a extension and what type of an extension cable, if any, from the controller to the start of the string? This includes the pigtails.
- Any zigzag strings, null pixels or is each string driven directly from a single controller output?
- Did you change the series termination resistors on the controller if so what values have you tried?
- Current output and number of power supplies?
- Wire size from controller to power supply? (You'd be surprised just how much voltage can be lost in 10" using a 14 AWG wire)
- Is it totally in a failure mode or does it come back at different times of the day or after being off for a while?
- Had you run the strings at full on for for a while before the issue showed up?
- Not that it matters but did you get caps for the end of the strings? Always a good idea.
- Did you put the red "O" rings on the male connectors so they stay waterproof? Sometimes Ray just sends them in a bag for you to put on.
My initial reaction is that I would not expect this massive of a failure in a single group unless there was a major manufacturing issue or a bad batch of chips. If these were all built on the same batch then both are possibilities that I would not discount.
I'm still leaning toward a series termination resistor or noise issue as a possibility especially since I'm seeing the failure pattern change. I'd like to see a longer video so I could judge that better however.
Between the WS2811/2/B the specification show 33 ohms typical although I've seen up to 75 ohms used. I still think that 270 ohms is too high although I've pushed 30 feet of lead before a 50 count string with the rest of the outputs running 50 count connected directly to the controller. BTW, even with a 12AWG cable 1' cable between the controller and the power supply I've seen about 0.25 to 0.35 volt drop and the cable gets warm, not hot, after a few hours of testing at all white.
Ok Let me see what I can answer for now. I am at work so this may come in a couple posts.
1. My order was for 32 strings of 50 nodes @ 6" spacing. and 30 strings of 60 nodes @ 6' spacing. I knew that I would have to cut to the length that I needed to fit. The longest ones that are on that part of the roof is 59 nodes. Remember mine are 1804s not 2811s. I was not expecting that, but that is what was ordered for me because in the begining my DLA stuff would not drive the TC nodes
2. They are being driven with Falcon 16s. The roof has 4 of them running 16 strings each. Some of the strings mind you are only 7 nodes long, but I would say the average overall would be 40-45 nodes per string. I do not own any Jsys stuff. All of my RGB equipment is DLA (Lynx) or Falcon.
3. I believe that the pigtails hook directly to the controllers are 18" in length and all of the strings are the factory connectors, I think they are 2 meters. There is one that I had to lengthen about 6" to reach the controller, but only 1.
4. I don't know what you mean about zigzag stings, but no nulls all are directly connected to the controllers.
5. There is no termination on these controllers. All are as per build.
6. When I first started I was using ATX power supplies on one controller. When issues started to arise I read that lowering voltage might help, so I ordered 30 amp power supplies. I have 11.6 volts right before the starting node and 10.6 at the end of the strings. I am using 2 30 amp power supplies on each controller.
7. I am using 12 gauge automotive wire from PS to controller all contained in a CG1500 case so maybe 12" each. 1 PS to 1/2 of the controller board.
8. Most are total failure, but some will come and go a little, but not many and they don't come for long! LOL
9. More to follow.
I have the same issues with some of these pixels, then when they receive signal they flicker.
jklingert wrote:I wonder if the compression force from tightening the lens and ring are transferring stress and damaging the internal wiring and chips? Is everyone that is having trouble using the lens assemblies?
I agree with this assumption. Mine worked when I got them, and after I cut them up and zip tied them to window frames. I had problems after I installed the covers. Some bulbs/pixels/rings where not as close to round as they could be. As a result I forced them on in some cases. When I replaced them with new strings, I was careful to stop twisting at the first hint of resistance. So far the new strings are still working plugged into the exact same cords, in the exact same locations as the ones that had failed.
Tom
