Technicolor Pixels
 
Notifications
Clear all

Technicolor Pixels

140 Posts
31 Users
0 Reactions
43.4 K Views
Posts: 17
(@rdebolt)
Active Member
Joined: 16 years ago
timon wrote:Id like to understand the layout.

  1. Looks like 29 strings of 50 pixels each.
  2. Custom built or standard lengths?
  3. Which controller and how many? (E681, E682, E6804 or J1Sys)
  4. How long of a extension and what type of an extension cable, if any, from the controller to the start of the string? This includes the pigtails.
  5. Any zigzag strings, null pixels or is each string driven directly from a single controller output?
  6. Did you change the series termination resistors on the controller if so what values have you tried?
  7. Current output and number of power supplies?
  8. Wire size from controller to power supply? (You'd be surprised just how much voltage can be lost in 10" using a 14 AWG wire)
  9. Is it totally in a failure mode or does it come back at different times of the day or after being off for a while?
  10. Had you run the strings at full on for for a while before the issue showed up?
  11. Not that it matters but did you get caps for the end of the strings? Always a good idea.
  12. Did you put the red "O" rings on the male connectors so they stay waterproof? Sometimes Ray just sends them in a bag for you to put on.

My initial reaction is that I would not expect this massive of a failure in a single group unless there was a major manufacturing issue or a bad batch of chips. If these were all built on the same batch then both are possibilities that I would not discount.

I'm still leaning toward a series termination resistor or noise issue as a possibility especially since I'm seeing the failure pattern change. I'd like to see a longer video so I could judge that better however.

Between the WS2811/2/B the specification show 33 ohms typical although I've seen up to 75 ohms used. I still think that 270 ohms is too high although I've pushed 30 feet of lead before a 50 count string with the rest of the outputs running 50 count connected directly to the controller. BTW, even with a 12AWG cable 1' cable between the controller and the power supply I've seen about 0.25 to 0.35 volt drop and the cable gets warm, not hot, after a few hours of testing at all white.

Okay let me see what I can answer here.

1. I actually ordered 30 strings of 60 nodes and 32 strings of 50 nodes, all at 6" spacing. I knew that I would have to cut to fit. I was not aware at the time that mine were ordered with the 1804 chip instead of the 2811. The reason that they were ordered that way is because I was having trouble getting my DLA (Lynx SSCs) to drive the test string that I received. That is why I went to the controllers that I am using now, because they would drive the 2811s at the higher bit rate speeds.
2. The strings are shortened to fit. The longest ones are 59 nodes and the shortest is 7 nodes. On average I would say that they are 40 to 45 nodes long.
3. Running 4 Falcon 16 controllers. i do not own any E or Jsys controllers. All of my RGB hardware is DLA or Falcon.
4. The pigtails are all the ones that came with the nodes. I believe that they are about 18" long. All string connectors are the factory length @ about 6' with the exception of 2 that needed extended about 6" more to reach the controller.
5. Not sure what a zigzag string is, but no nulls. They are all connected directly to the controllers.
6. There are no terminations on these controllers. They are as per build.
7. Each controller has 2 30 amp power supplies. Each driving 1\2 of the board or 8 strings. I have the voltages turned as low as they will go, because I read somewhere that might help. I actually started on my first controller using and ATX PS, but after I started having issues, I bought the 30 amp supplies.
8. I am using 12 gauge automotive wire form PS to controllers. About 12" as they are all housed together in a CG1500 case.
9. Most are total failure. There are a few that come and go, but they do not come for very long! LOL It appears to me that I have many more failures after a power off and restart.
10. All of the strings were burnt in for at least 24 hours. After the first batch I put on the roof started having issues I started burning longer, some for up to 3 to 4 days. All inside and I never have had a failure until they were outside. All were on a cycle of RGBW for about a 3 second per color cycle. Never at a sustained all white. Temperature may have something to do with it as our outside lows have been in the teens for quite some time now.
11. I did get caps, but since they are all cut on the end I have not used them. What I do is make a diagonal cut on the end then shrink wrap the end and I use the shrink wrap with glue for that.
12. I Did not get the red orings with my order; how ever I had a bunch from my others that I used. I don't really think that they are necessary with the TC connectors anyway. Those things are a bear to put together! 🙂

I will take a longer video tonight. Not that you will see much because most do not work. I will also take a picture with just power applied to controllers. I agree about such a high failure, but My Megatree is running just fine with Falcon controllers and standard IP68 1804 nodes.

My voltages are 11.6 volts at the first node and 10.6 volts after the last.

Thank you for taking the time to help! I really do appreciate it!
Roger


Reply
Posts: 17
(@rdebolt)
Active Member
Joined: 16 years ago
timon wrote:Id like to understand the layout.

  1. Looks like 29 strings of 50 pixels each.
  2. Custom built or standard lengths?
  3. Which controller and how many? (E681, E682, E6804 or J1Sys)
  4. How long of a extension and what type of an extension cable, if any, from the controller to the start of the string? This includes the pigtails.
  5. Any zigzag strings, null pixels or is each string driven directly from a single controller output?
  6. Did you change the series termination resistors on the controller if so what values have you tried?
  7. Current output and number of power supplies?
  8. Wire size from controller to power supply? (You'd be surprised just how much voltage can be lost in 10" using a 14 AWG wire)
  9. Is it totally in a failure mode or does it come back at different times of the day or after being off for a while?
  10. Had you run the strings at full on for for a while before the issue showed up?
  11. Not that it matters but did you get caps for the end of the strings? Always a good idea.
  12. Did you put the red "O" rings on the male connectors so they stay waterproof? Sometimes Ray just sends them in a bag for you to put on.

My initial reaction is that I would not expect this massive of a failure in a single group unless there was a major manufacturing issue or a bad batch of chips. If these were all built on the same batch then both are possibilities that I would not discount.

I'm still leaning toward a series termination resistor or noise issue as a possibility especially since I'm seeing the failure pattern change. I'd like to see a longer video so I could judge that better however.

Between the WS2811/2/B the specification show 33 ohms typical although I've seen up to 75 ohms used. I still think that 270 ohms is too high although I've pushed 30 feet of lead before a 50 count string with the rest of the outputs running 50 count connected directly to the controller. BTW, even with a 12AWG cable 1' cable between the controller and the power supply I've seen about 0.25 to 0.35 volt drop and the cable gets warm, not hot, after a few hours of testing at all white.

Ok I answered every question on here and got a message that my reply would not be posted until a moderator review. I don't think that I said anything wrong just answered the questions yet my reply has not been posted. Don't know what I did wrong here either! LOL Maybe it's just me!!!


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
rdebolt wrote:Ok I answered every question on here and got a message that my reply would not be posted until a moderator review. I don't think that I said anything wrong just answered the questions yet my reply has not been posted. Don't know what I did wrong here either! LOL Maybe it's just me!!!

Might have something to do with your low post count and the anti-spamming SW for board...


Reply
g2ktcf
Posts: 3651
(@g2ktcf)
Famed Member
Joined: 18 years ago

Just FYI,

The Technicolor pixels are NOT Ray's design. Ray is currently manufacturing them and he has some SERIOUS quality issues that a few of us have been working on. All you can do at this point is send him a request for warranty replacements that YOU WILL PROBABLY NOT GET FOR THIS YEAR.

For those of us involved with the Technicolor Pixels, this quality issue is a slap in the face as the design is 100% sound. Its the QC issues with the manufacturing process that are causing problems.

Chris


Reply
Macrosill
Posts: 9739
(@macrosill)
Member
Joined: 20 years ago
rdebolt wrote:Ok I answered every question on here and got a message that my reply would not be posted until a moderator review. I don't think that I said anything wrong just answered the questions yet my reply has not been posted. Don't know what I did wrong here either! LOL Maybe it's just me!!!

It was posted yesterday at 3:49 PM. No links so the post did not require validation.


Reply
Page 7 / 28
Share: