I understand that the TC case is not Rays design but is that totally true of the logic board? It looks like a repackage of another of Rays pixels that includes a regulator. I've already looked at those and found an issue that worried me. I have a PCB that I believe is the one used in the TCs and it has the same issue. Until I open up one of mine I won't know for sure.
Knock on wood but so far mine are working fine. The last of them go up over the next couple of days so well see what happens then. When they are all up it's about 800 pixels.
As far as quality issues I've not seen any on mine yet. That doesn't mean there aren't any just that I've not seen any. Mine were built earlier this month so not part of the group buy most of the others are using.
g2ktcf wrote:Just FYI,The Technicolor pixels are NOT Ray's design. Ray is currently manufacturing them and he has some SERIOUS quality issues that a few of us have been working on. All you can do at this point is send him a request for warranty replacements that YOU WILL PROBABLY NOT GET FOR THIS YEAR.
For those of us involved with the Technicolor Pixels, this quality issue is a slap in the face as the design is 100% sound. Its the QC issues with the manufacturing process that are causing problems.
Chris
Zachary Stoltenburg has stated that he designed the circuit boards for the Technicolor Pixels. I am not positive but I think he claims he designed *everything* about them. Wire, case, circuit board, etc.
timon wrote:I understand that the TC case is not Rays design but is that totally true of the logic board? It looks like a repackage of another of Rays pixels that includes a regulator. I've already looked at those and found an issue that worried me. I have a PCB that I believe is the one used in the TCs and it has the same issue. Until I open up one of mine I won't know for sure.Knock on wood but so far mine are working fine. The last of them go up over the next couple of days so well see what happens then. When they are all up it's about 800 pixels.
As far as quality issues I've not seen any on mine yet. That doesn't mean there aren't any just that I've not seen any. Mine were built earlier this month so not part of the group buy most of the others are using.
I have cut apart one of mine. There is NO regulator in mine. I am not an electrical engineer by ANY stretch of the imagination, but all I see in mine are the 1804 chip, led, resistors and what I am assuming (you know what that does) are capacitors. So regulator failure is out for mine.
Gary, all we can do now, unless Zack come into the forums, is FIX the issue. The TC design has us in mind and I think once we get past whatever is the problem..they will be a solid pixel for the community. I cannot pass judgement until the season is a few weeks in...I think timon, with the help of Steven inspecting the failed pixels, can get us down the road. I would like to see this fixed by next year. I will wait until the end of Dec to request anything from Ray...but if they fail...I'll be asking for replacements AFTER the design/issue is fixed. Timon..you might want to work with Chris over at Radiant Holidays or at least keep each other in the loop or the conversations between the two of you and Ray will get confusing I'm sure. This needs to be worked on as a group with results coming from one source.
While trying to figure out what is going on with mine I want to point out one thing. I AM NOT BITTER towards anyone or anything.....yet. Am I frustrated ABSOLUTELY. Will I have the show that I imagined....not this year. Have I put a lot of time and effort into this.... Yes. Do I have A LOT of money tied up.....yes. How ever I WILL have a show and people will enjoy it. As long as in the end the right thing is done I will be happy. What I see as the "right" thing at this point is replacement of all of my strings with something that I can use. Stuff happens, people make mistakes, I for one don't go through a day without making at least one. I look at it this way now, I will be WAY ahead of next year's display! LOL In the end I still have my health, my friends and my family. They are the most important thing to me!!! I have been blessed and am VERY thankful!
Now I will try to answer all the the questions again!!!
To be fair, until I see the actual PCB used in the Technicolor Pixels I should not say what my concerns are because I'm not 100% sure the PCBs I have are the ones used on the Technicolor's. When I can confirm that are then I will post what I think is an issue.
rdebolt, PM me your specs and setup. Also, while my TC's are working, FOR NOW, I purchased the TC's to put on my roof line and peaks because those are the most inaccessible areas to get to with a failure. SO instead of using what I had LAST year on the roof and peaks..I put the TC's on and used my old ones on the windows and wreaths so I could get to them....time will tell if this was a STUPID move or not.
I'd be happy to work with Chris and Steven on this. We should exchange numbers and Skype addresses.
MindTrik wrote:Gary, all we can do now, unless Zack come into the forums, is FIX the issue. The TC design has us in mind and I think once we get past whatever is the problem..they will be a solid pixel for the community. I cannot pass judgement until the season is a few weeks in...I think timon, with the help of Steven inspecting the failed pixels, can get us down the road. I would like to see this fixed by next year. I will wait until the end of Dec to request anything from Ray...but if they fail...I'll be asking for replacements AFTER the design/issue is fixed. Timon..you might want to work with Chris over at Radiant Holidays or at least keep each other in the loop or the conversations between the two of you and Ray will get confusing I'm sure. This needs to be worked on as a group with results coming from one source.
MindTrik wrote:rdebolt, PM me your specs and setup. Also, while my TC's are working, FOR NOW, I purchased the TC's to put on my roof line and peaks because those are the most inaccessible areas to get to with a failure. SO instead of using what I had LAST year on the roof and peaks..I put the TC's on and used my old ones on the windows and wreaths so I could get to them....time will tell if this was a STUPID move or not.
Yeah, My highest pixels are 45 feet in the air (straight up palm trees). I spent a lot of time zip-tying to vinyl coated aircraft cable to the point I think I gave myself carpal-tunnel. So far (knock knock knock) all those sets are holding up. The guys I hired to climb up the trees did a great job of securing them, so they don't move at all and the neighborhood crows seem to be leaving them alone. They do look great lit up, but I wish I had more. I'm really hoping they hold up. I have one set I'm going to replace, luckily on a low part of the house and since the "twinkling" windows are symmetrical, I'm just going to tell people I meant to do it.
timon wrote:Id like to understand the layout.
- Looks like 29 strings of 50 pixels each.
- Custom built or standard lengths?
- Which controller and how many? (E681, E682, E6804 or J1Sys)
- How long of a extension and what type of an extension cable, if any, from the controller to the start of the string? This includes the pigtails.
- Any zigzag strings, null pixels or is each string driven directly from a single controller output?
- Did you change the series termination resistors on the controller if so what values have you tried?
- Current output and number of power supplies?
- Wire size from controller to power supply? (You'd be surprised just how much voltage can be lost in 10" using a 14 AWG wire)
- Is it totally in a failure mode or does it come back at different times of the day or after being off for a while?
- Had you run the strings at full on for for a while before the issue showed up?
- Not that it matters but did you get caps for the end of the strings? Always a good idea.
- Did you put the red "O" rings on the male connectors so they stay waterproof? Sometimes Ray just sends them in a bag for you to put on.
My initial reaction is that I would not expect this massive of a failure in a single group unless there was a major manufacturing issue or a bad batch of chips. If these were all built on the same batch then both are possibilities that I would not discount.
I'm still leaning toward a series termination resistor or noise issue as a possibility especially since I'm seeing the failure pattern change. I'd like to see a longer video so I could judge that better however.
Between the WS2811/2/B the specification show 33 ohms typical although I've seen up to 75 ohms used. I still think that 270 ohms is too high although I've pushed 30 feet of lead before a 50 count string with the rest of the outputs running 50 count connected directly to the controller. BTW, even with a 12AWG cable 1' cable between the controller and the power supply I've seen about 0.25 to 0.35 volt drop and the cable gets warm, not hot, after a few hours of testing at all white.
1. I ordered 30 strings of 50 nodes and 32 strings of 60 nodes. They are @ 6" spacing. Mine came with the 1804 chips because I was having trouble driving the "test" string with my DLA (Lynx) SSCs.
2. They are all shortened to fit. The longest strings are 59 nodes and the shortest are 7 nodes. I would say they are an average of 40 to 45 nodes in length.
3. They are being driven with 4 Falcon 16 controllers. 16 strings to a controller. I do not own anh E or Jsys hardware.
4. The pigtails are the ones that came with my order. I believe that they are about 18" long. The connectors are all the factory ones with the exception of 2 that I needed to add about 6" more to reach the controller. They are about 6' long.
5. I do not know what a zigzag string is, but there are no null nodes. They are connected directly to my controllers.
6. The 16s have no terminations and they are all built to spec.
7. I am using 30 amp power supplies. There are 2 to a controller. So 30 amps to 8 strings. Voltages are turned as low as they can be. A failing string that I have has 11.6 volts at the first node and 10.6 volts at the end of the string
8. Using 12 gauge automotive wire. About 12" long as they are all housed together in a CG1500 case.
9. Most are total failure. A few will come and go, but if they come it is only for a very short time! LOL Removing power and returning power later seem to take out more nodes than fix any.
10. All strings were run through a RGBW test cycle. Never at a sustained all white. The first were a 24 hour burn in. After I put them on the roof and started having issues I started to burn them in at least 48 hours. Some even longer. One note here: I NEVER had a failure in the house only after being outside. We have not had bad weather, but it has been very cold. Lows in the teens with highs in the 30s.
11. I did get caps but since they have all been shorted I have only used a couple. I finish the end of my string with a diagonal cut the shrink wrap the end. I use shrink wrap with glue in it.
12. I did not receive any o-rings with my order, but used some that I had with my other connectors from a previous purchase. I must say though that I don't think that the o-ring is necessary with these strings. They are an absolute bear to put together and get the screw tight!
Here are some videos that I took last night. One of them is all of the nodes "static" no data going to them.
