Technicolor Pixels
 
Notifications
Clear all

Technicolor Pixels

140 Posts
31 Users
0 Reactions
43.4 K Views
Steven010
Posts: 416
(@steven010)
Honorable Member
Joined: 18 years ago

Also;

It appears all paths lead back to WorldSemi. Someone needs to get them engaged. First, I would ask them what happens to part if VDD =0V and Data in = 5V? especially if an LED is attached?
Second, what happens if 12v is applied to Data pin, even for milliseconds?

BTW, it appears WorldSemi likes Ray Wu, he is mentioned repeatedly on Facebook site;

I submit he could engage WorldSemi and get some proactive corrective action. Maybe even free design services.

Actually, first I would ask them to re-write data sheet....And please find out what it means"

ABSOLUTE MAXIMUM RATINGS

Power supply +6.0 ~ 7.0 VDC
OUTPUT Voltage VOUT 12V "
???


Reply
Steven010
Posts: 416
(@steven010)
Honorable Member
Joined: 18 years ago
MindTrik wrote:YES...I forgot to note!!!! DO NOT DO A HOT SWAP ON THESE PIXELS!!! I DID with one of the ones Steve has and it fried a pin on my e6804 CPU...

Also, why does the E6804 fail when hot plugged? I dont have schematic, but I can guess...Again, the pixel inadvertently applies 12V to data pin, I am sure E6804 driver output is not tolerant to being forced to 12V, even through a resistor. I really like the San Devices design, but I think this attribute could be improved. However, it is poosible any improvement here will promote more failure to the pixels...


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

I quick fix might be a shut regulator on the data pin. AKA: a 5v zener diod across the data and GND pin. (Any voltage above 5v gets passed though and converted to heat.)

But the propellers chip current limiting is good for a 500ma it really should not be an issue. if data pin just has a a pull up type resistor or something on it.

Also guys never fully trust the spec sheets always do your own testing. You can get some odd issues even on simple devices.


Reply
Steven010
Posts: 416
(@steven010)
Honorable Member
Joined: 18 years ago

John,

Water Ingress was through the wire strands, not insulation-not sure how, but if this was first pixel or if wires were spliced at this point, it could explain. These appear to be well sealed.

I did not open pixel #4 or #5, #4 behaved exactly like #3, and #5 appears to have no issue. Kevin confirms he thinks he sent one good one....

So far, I have seen no evidence that heat of LDO or WS2811 contributed to failure. All problems seem to indicate the WS2811 failed due to EE overstress.

Ideally, I would like to get my hands on more failures. Smoking gun is here somewhere...

timon wrote:Stayed away from the forum for a day as I was busy getting the display up and running. Still have one set of lights and some cleanup to do. Hopefully I can go line Wednesday night. Anyway here are my comments on the findings.

That's the same board current used in the Technicolor's.

  1. Did it look like the water came through on the outside of the insulation or did it somehow get into the wire and come in that way?
  2. Sounds like the input was damaged. A design change I sent to Ray should fix that problem.
  3. Data input, see #2. I don't understand the low current either. Did you test a working pixel to see what current level you get. I can try that with some of the PCBs I have here.
  4. Same as 3
  5. Did you open this one up?

This is what I expected if the regulator thermal protection was working. What you found is confirming what I expected was the problem based on the design.

I've found another regulator that should work much better than the 78L05. It has a much higher junction temperature of 150C, lower dropout of about 0.5V instead of 1.7V, lower quiescent current of about 5ua instead of 2ma, a 0.5W rating, thermal shutdown and lastly it looks to be about the same price as the 78L05.

Yep, I really think this is either a EDS or the input got shorted to +V. When the WS2811 is taken out current goes up then the temperature goes up and the PCB starts to scorch. Classic cascade failure.

As you can see there are no input and output resistors on the current board. Those resistors are there for two reasons, first to act as series terminations and second to protect the input to the chip from hot plugging and voltage spikes such as ESD. That is one of the design changes that I had Ray make.

Yep, those are the changes that I had Ray make.

I'm talking with Ray right now. He's sending me the PCB files to check. Will report back later.

John


Reply
Steven010
Posts: 416
(@steven010)
Honorable Member
Joined: 18 years ago
kingofkya wrote:I quick fix might be a shut regulator on the data pin. AKA: a 5v zener diod across the data and GND pin. (Any voltage above 5v gets passed though and converted to heat.)

But the propellers chip current limiting is good for a 500ma it really should not be an issue. if data pin just has a a pull up type resistor or something on it.

Propeller chip does not appear to connect to output pins, rather the 74HCT541 appears to. Likely this is part failing...

OOPS! just looked at assembly manual for 6804, you are correct, appears to connect direct to Propeller chip. Same question applies, what happens to Propeller if 12V is applied to I/O pin????


Reply
Page 22 / 28
Share: