Strange AlphaPix4 H...
 
Notifications
Clear all

Strange AlphaPix4 Hardware Behavior

11 Posts
7 Users
0 Reactions
3,229 Views
Posts: 10
Topic starter
(@ibanezsvo)
Active Member
Joined: 11 years ago
[#43937]

Background, my AlphaPix4 controller is hooked up using only 2 outputs, and I only use HC Brilliant Bulbs on it. Out2 feeds roof outline - about 280 bulbs w/ power injection. Everything here works fine. Output1 hooked up to three window frames, each in series from Window1 then 2 then Window3. Each frame is 21 bulbs each so I'm not experiencing power issues (as proven below). Window 2&3 are right next to each other and connected via a short 5' jumper (HC's 3/C wire). The intended hookup is: Out1 -> Window 1 then a 15' jumper to Window2 and then short jumper to Window3.
I believe this is a hardware issue because I experience the same results in Test Mode on the controller and using xLights output. Here is the problem and some tests I've run and their results
When connected as desired, Window1 works fine, Window2 two gets the first 2 or 3 bulbs that act right then the next bulb flickering, then nothing - including Window 3, nothing.
Windows 2&3 hooked up alone, no problem.
Windows 1,2,&3 hooked up with short jumpers between each - no problem.
Window 1 hooked up (working fine) then to test power concerns I connected a new brilliant bulb string 50 bulbs/10" spacing and all bulbs (total 71) lit up and worked as expected.
I did some impedance tests on each conductor going from end to end (bulbs and controller disconnected) and got about 1ohm on each wire.
Same wire used in the 5' jumper as in the 15' jumper and I've replaced the 15' jumper with a different piece and I've even run two pieces in parallel.
I can't figure out what to do next and have no idea what is causing this.


10 Replies
StickyWicket
Posts: 548
(@stickywicket)
Honorable Member
Joined: 14 years ago

15 feet is too far with without a null pixel using that wire. At least that has been my experience.

"Windows 1,2,&3 hooked up with short jumpers between each - no problem." this tells you your pixels are too far apart at 15' throw a null pixel (or two) in between your 15 feet span and you should be good.

You can read more about null pixels in the WIKI: http://www.doityourselfchristmas.com/wiki/index.php?title=Null_Pixels


Reply
Posts: 86
(@markrvp)
Estimable Member
Joined: 19 years ago

It's not the controller since everything works as it should when you remove the 15' cable. Since you are only using 2 of the 4 outputs from the controller, why not hook window 2 & 3 up to output 3 of the controller? It would be easy enough to set up that SPI output to have the same universe/channel assignments so that nothing changes in your sequencer setup.

I can tell you that I am running 4 different strings of Brilliant Bulbs from an Alphapix 4 where the first pixel is connected by a 25' cable with NO problems. But that length of cable is at the very beginning.


Reply
Posts: 61
(@ghormann)
Trusted Member
Joined: 15 years ago

on my Alphapix 4 controllers, I have no problem going 20ft from controller to first element. When going between HC Brilliant Bulbs, 10ft is about the max I've found to be stable.


Reply
StickyWicket
Posts: 548
(@stickywicket)
Honorable Member
Joined: 14 years ago

Just curious what wire you guys are using to go 20' to 25' from the AlphaPix4. I couldn't get anywhere near that with the 3 core wire HolidayCoro sells.


Reply
Page 1 / 3
Share: