I wanted to run 2 different voltage type 12v and 5v pixels from the same e682. I understand that you can split 1-1 through 2-4 and 3-1 through 4-4 respectively. But I needed to send 3-1 through 4-4 to a different location and power inject with a different voltage(5v). So here are my questions
1. If I only send the data to the different location do I still need to power the 2nd half of the board?
2. If I do need power it, can it be 12v that im using in the enclosure or does it have to be 5v?
Thanks Rob
Robo wrote:1. If I only send the data to the different location do I still need to power the 2nd half of the board?
I'm pretty sure both halves of the board will need power to process data. It would be an easy test though.
2. If I do need power it, can it be 12v that im using in the enclosure or does it have to be 5v?
I don't see why it couldn't be 12v. Just make sure J21 is set correctly - jumper between pins 1 and 2, and a jumper between pins 3 and 4. Some pixel types need a common ground, but otherwise this should work fine.
Not 100% sure on your question but I run one of my E681's (same power layout as E682) with split voltages. IMO it's better to run the logic (right side) of the board with 12v and let the regulation on the board provide a smooth 5v vs trusting the supply from a 5v supply that is also powering the pixels since it can dip quite a bit depending on the load.
If I understand correctly, he's looking at running the E682 with a single 12 volt supply, but sending some of the data outputs to 5v pixels which will be powered separately from a 5v supply. So long as the E682 power and the pixel power are entirely isolated, I don't see any problems.
J19 is the main power source for the board's Logic IC's If you power it from a 5v supply jumper 2 & 3 on J21 this will supply 5V to the logic and 5V to the connectors 3-1 - 4-4, If you supply 12V to J19 jumper 1 & 2 and 3 & 4 this will supply 5V to the logic and 12v to connectors 3-1 - 4-4 you will always have data and ground on all connectors 1-1 to 4-4 even if you do not apply power to J18 but you will not have any power in the connectors 1-1 - 2-4. If you use another power supply for data from 1-1 - 2-4 remember you must connect your ground from that supply to the E682 ground (-) J18. I hope I am looking at you question from the same angle you are.
Gary
The Sansdevice only needs power to operate. It does not need to distribute power to the pixels at all, so yes, you can power the pixels at the other end of the data wire. Some of my pixel strings are hardwired to 12 volt 2A wall warts similar to the type to power home routers and modems. All that connect to the controller or bridge is ground for data and data. I've standardized on using RJ45 for data as I have a DYILEDexpress DMX bridge which is very similar to the SansDevices products except it does not distribute power. If I wanted to connect my pixels to a SansDevices, I would simply bring out Data and Ground to an RJ45 jack and connect the pixels.
Hardwired power prevents accidents with pixel voltage. Data is 5 volt regardless of pixel voltage. Adding an RJ45 jack on the far end of pixel strings makes adding strings for configuration with automatic power injection due to attached supplies is perfect for the mobile DJ shows. Plug the strings together as needed and apply power. No worries about how many pixels to a power supply while on the road.
I'm out with the Motorhome on the Oregon Coast this weekend at a big family campout bash. I've already decorated for tonights evening activities.
If I understand correctly, he's looking at running the E682 with a single 12 volt supply, but sending some of the data outputs to 5v pixels which will be powered separately from a 5v supply. So long as the E682 power and the pixel power are entirely isolated, I don't see any problems.
Do connect the Ground of both. Data requires a common data ground. Don't connect +12V to +5V. It lets out the magic smoke.
Technician wrote:
I'm out with the Motorhome on the Oregon Coast this weekend at a big family campout bash. I've already decorated for tonights evening activities.
I am curious to see the decorated motor home. Are you willing to share any pictures of this in action?
Not much to see. Just a string of pixels from the awning bar. Using S hooks for a string for some color. Not running a sequence. Using some of these and a string.
They slide into a slot in the bar. Keeps the bugs away from the door unlike the porch light. Don't need the swarm right at the door.
After dark I may snap a shot.
thanks guys for all the help that is exactly what I was looking for 🙂

