Notifications
Clear all

Ray Wu's Pixels

11 Posts
8 Users
0 Reactions
4,107 Views
Posts: 3
Topic starter
(@deezee)
Active Member
Joined: 10 years ago
[#45335]

First post. I purchased some 12mm WS2811 led smart pixel nodes with all black wire. I'm trying to find out which are the positive and which are the negative wires. I assumed the data is the middle one. He did send me a note telling me but I'm sorry I do not understand them. They are as follows:

wiring instruction:

input:the side without IC of the pcb
the first wire from left: DC12V+
middle wire: DAT
the left wire from the left : GND

Anyone show me a photo or explain his instructions?

Thanks a lot.


10 Replies
tucsonlights
Posts: 667
(@tucsonlights)
Honorable Member
Joined: 15 years ago
deezee wrote:First post. I purchased some 12mm WS2811 led smart pixel nodes with all black wire. I'm trying to find out which are the positive and which are the negative wires. I assumed the data is the middle one. He did send me a note telling me but I'm sorry I do not understand them. They are as follows:

wiring instruction:

input:the side without IC of the pcb
the first wire from left: DC12V+
middle wire: DAT
the left wire from the left : GND

Anyone show me a photo or explain his instructions?

Thanks a lot.

Are these bullet nodes or technicolors? If the cover on the pixels are clear just shine a flashlight on the pixel and read the circuit board to see what is +, -, dat. If they are technicolor then lay the string down running away from you. Then use rays decoding. Left +, middle data, right -


Reply
Posts: 740
(@ezellner)
Prominent Member
Joined: 11 years ago

I think he meant last wire from the left...was ground.


Reply
Posts: 3
Topic starter
(@deezee)
Active Member
Joined: 10 years ago

These are the one I purchased.

https://www.aliexpress.com/store/product/100pcs-DC12V-12mm-WS2811-led-smart-pixel-node-with-all-black-wire-20AWG-IP68-rated/701799_1932863171.html?spm=2114.12010612.0.0.2nXr7U

I'm having a tough time trying to read the board with my 50 year old eyes. I'l have to purchase a magnifying glass. lol


Reply
tucsonlights
Posts: 667
(@tucsonlights)
Honorable Member
Joined: 15 years ago
deezee wrote:These are the one I purchased.

https://www.aliexpress.com/store/product/100pcs-DC12V-12mm-WS2811-led-smart-pixel-node-with-all-black-wire-20AWG-IP68-rated/701799_1932863171.html?spm=2114.12010612.0.0.2nXr7U

I'm having a tough time trying to read the board with my 50 year old eyes. I'l have to purchase a magnifying glass. lol

Just use a glass of water and hold it over the pixel. Shine a light on the pixel. You really only need to find + and Di.


Reply
Posts: 128
(@emuney18)
Estimable Member
Joined: 11 years ago

Look at the node and the black square about 5mm x5mm is the IC. That's what he means. Opposite side of that is input. Then left is hot middle data and right is ground.

Sent from my iPhone using Tapatalk


Reply
Posts: 3
Topic starter
(@deezee)
Active Member
Joined: 10 years ago

Got it thanks!


Reply
aknflyer
Posts: 371
(@aknflyer)
Reputable Member
Joined: 10 years ago

I'm having a tough time trying to read the board with my 50 year old eyes. I'l have to purchase a magnifying glass. lol

I use whats called a jewelers loupe, 10-15 power magnification. Makes a difference when glasses are not enough. Getting old eyes.


Reply
Posts: 94
(@davros)
Estimable Member
Joined: 13 years ago

Just went thru this myself:

So, dipping one in a full shotglass plus using my Optivisors - I can just make out GND DO 12v on the WS2811 side.

Reply
Posts: 535
(@mharnish)
Honorable Member
Joined: 12 years ago

I just wipe spit or water across the plastic and it makes it fairly clear. You can then use a magnifying glass if needed but the water or spit helps tremendously.


Reply
Page 1 / 2
Share: