Question about grou...
 
Notifications
Clear all

Question about grouping

20 Posts
7 Users
0 Reactions
6,261 Views
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago
aaron1 wrote:I don't mean to be rude, but Richard1 is confusing all of the terminology by using the wrong words to describe the various setup items on the board.

1. A socket refers to an a virtual Ethernet path used by the board. You can assign different physical DMX universe numbers to each socket. There are 6 sockets on a E682 board. I think an E681 has 4 sockets. I don't own an E681, so someone correct me if I'm wrong.
2. A cluster refers to a set of 4 connectors that are used to connect your pixel strings to the board. You can assign a socket (and thus, its associated universe) and a starting DMX address to each cluster.
3. A cluster can end up spanning multiple universes. For example, you could connect qty 4 50-pixel strings to a single cluster (one to each of its 4 connectors), for a total of 200 pixels on that cluster. That would require 600 DMX addresses. Thus, more than one universe on that cluster. If you started the cluster on universe 1, address 1, and had universe 2 assigned to the next socket, those pixels would span from Unv1-001 to Unv2-090.
4. A single universe can span multiple clusters. In the above example, the last 30 pixels would consume 90 addresses of the next assigned universe, as you can see. You could start cluster 2 on Universe 2, address 091.
5. For clarity on the OP, GRoup is a command that allows groups of pixels to be assigned the same DMX address, if that's what you'd like to do. For example, if you used a grouping of 2 on a string of 50 pixels, you would only consume 25 RGB addresses (75 DMX addresses), as every 2 pixels would be told to behave exactly the same way.

And for the sake of completeness, I assume that the data for a single universe is transferred over each socket, and that conversely the data for each universe is transferred through one socket (i.e. a one-to-one mapping).


Reply
Posts: 16
(@richard1)
Eminent Member
Joined: 15 years ago

look at my reference , it states e681 , I believe your confused .


Reply
Posts: 213
(@aaron1)
Estimable Member
Joined: 16 years ago

According to Sandevices website, the setup is the same. The only difference is that there are 4 sockets on the E681 and 6 on the E682. Sockets were also called "slots" in a prior rev of the user's manual.

The GRoup command applies to a whole cluster. And sockets/universes are a 1-to-1 mapping.


Reply
Posts: 2168
(@djulien)
Noble Member
Joined: 19 years ago

(deleted)


Reply
Posts: 1249
(@jstjohnz)
Noble Member
Joined: 17 years ago

Sockets and universes are mapped 1:1. Originally it was true that 1 universe was assigned to 1 cluster. Now that restriction is gone and any cluster can be mapped to any number of channels. The default configuration for the E681 was 1 universe per cluster so I think that has caused some confusion.

FWIW, a cluster corresponds to the pixel outputs that are driven by a single cog of the prop cpu. 4 cogs are devoted to driving pixel outputs, thus 4 clusters of outputs. Each pixel cog drives 5 output pins, a data line for each output and a common clock line. The parameters that apply to an entire cluster include the pixel type, string length, grouping, and zigzag. Per-string parameters include reversing (basically says that string is being driven from the far end) and null pixels. The string length could be done on a per string basis, but it's not that way now. Addresses are also assigned on a per-cluster basis. You specify the starting address (the address of the 1st pixel of the 1st string), and the pixels for all strings in the cluster are assigned sequentially from there.


Reply
Page 4 / 4
Share: