As most pixel failures (communications wise) are either the output chip of the last good one, or the input chip of the first bad, when we have time we cut the line between the two and attach a short string of pixels we carry that has alligator clips attached. If the test string light up then it was the first bad one. If they don't, then we know it was the last "good" pixel (not sending data). With as many pixels as we have replaced over the decade, this has saved quite a few.
To be honest, in the field with the weather turning cold, windy and sometimes wet, we have given in to the "last good and first bad" replacement method.
Once again, if we have time then we insert the test pixels.
I am having exactly the same problems with all the Paul Zhang pixels I bought last year. I have about 9000 in my display and have replaced over 100 bad pixels, so really 200 since I cut out last working and first dead one. I have not had one night where at least one prop did not have a problem. I fixed my fascia pixels by unplugging them since I was sick of climbing the ladder, weather in North Florida the last few weeks has not been good ladder weather. I am hoping the new evo pixels from Mattos might help next year.
DILA wrote:I am having exactly the same problems with all the Paul Zhang pixels I bought last year. I have about 9000 in my display and have replaced over 100 bad pixels, so really 200 since I cut out last working and first dead one. I have not had one night where at least one prop did not have a problem. I fixed my fascia pixels by unplugging them since I was sick of climbing the ladder, weather in North Florida the last few weeks has not been good ladder weather. I am hoping the new evo pixels from Mattos might help next year.
I'm in Jacksonville myself, I'm sure you got the same beating we did last weekend.
I do have to say, after a few dry/sunny days, almost all of my pixels have returned to normal, assuming some moisture/rain got in there and was causing noise on the data line, it has since evaporated and the majority of them are working again.
I did see the new YPS Duo pixels that came out not long ago, sad they're so expensive, but man it would be great if a pixel died and I could just ignore it lol.
I have not been so lucky. Last night I had a peace stick and a mega tree string with dead and stuck pixels. So far every problem has been 2022 pixels except one 2023 pixel on a candycane.
I've started using the 'pebble' pixels (bulk packaging) on some of my props this year (about 2,000 pixels total) and kept testing them while I added groups to each prop. I think I had about 15 or 20 pixels that were bad "out of the box" which were discovered during the initial installation testing. For repairs I've been using some of those nifty little heat-shrinks that have a solder ring inside and some sealer on each end to keep the weather out. Those are pretty nice but you need a good heatgun to effectively use them (without melting everything else around them).
I did end up replacing a couple more pixels after I put out the props but I guess, judging from what you guys have experienced, my pixel failures weren't too bad. After that thinks have settled out and worked pretty well, even during the rains we've had the last few days.
While troubleshooting the bad pixels I came up with a little trick to discover the bad pixel... I use a couple of straight-pins (with the little ball on the finger end) with a clip-lead jumper, and I just poke the pin into the input data line and the other pin into the output side of the pixel data line to bridge across the pixel. Most of the time I'm able to verify the pixel that has the output problem because the rest of the string after it starts functioning again. I've only had one problem where this method didn't work, where the last pixel just stayed on all the time and nothing after it would work. I think it might have had a short in the data output... I just replaced it and got the string working again. Anyway, the straight-pin / clip lead jumper trick kept me from replacing the wrong pixel almost every time. The pins made such small holes that the insulation would pretty much close up when it was removed, although a dot of super glue gel or something like that would be sure to seal the hole if need be.
