Pixel Reliability I...
 
Notifications
Clear all

Pixel Reliability Issues/Expected Lifespan?

26 Posts
10 Users
0 Reactions
4,780 Views
Posts: 1420
(@1pet2-9)
Noble Member
Joined: 6 years ago

I must be moving up.in the world. Last year, it was me getting slaughtered by the bad pixel nightmare. This year, it's my moving head. It's garbling the data and failing to pass it on down the chain. The secret elf gamemasters must rig it so as you level up, the problems get harder and more expensive.


Reply
Posts: 62
 DILA
(@dila)
Trusted Member
Joined: 19 years ago
1pet2_9 wrote:I must be moving up.in the world. Last year, it was me getting slaughtered by the bad pixel nightmare. This year, it's my moving head. It's garbling the data and failing to pass it on down the chain. The secret elf gamemasters must rig it so as you level up, the problems get harder and more expensive.

I think I'll stay with $30 of bad pixels, with the cost of some of the moving heads I can't imagine having to replace one. Hope you get the data problem fixed.


Reply
Posts: 34
(@fabiousa7)
Eminent Member
Joined: 11 years ago
OptykMuse wrote:I've started using the 'pebble' pixels (bulk packaging) on some of my props this year (about 2,000 pixels total) and kept testing them while I added groups to each prop. I think I had about 15 or 20 pixels that were bad "out of the box" which were discovered during the initial installation testing. For repairs I've been using some of those nifty little heat-shrinks that have a solder ring inside and some sealer on each end to keep the weather out. Those are pretty nice but you need a good heatgun to effectively use them (without melting everything else around them).
I did end up replacing a couple more pixels after I put out the props but I guess, judging from what you guys have experienced, my pixel failures weren't too bad. After that thinks have settled out and worked pretty well, even during the rains we've had the last few days.

While troubleshooting the bad pixels I came up with a little trick to discover the bad pixel... I use a couple of straight-pins (with the little ball on the finger end) with a clip-lead jumper, and I just poke the pin into the input data line and the other pin into the output side of the pixel data line to bridge across the pixel. Most of the time I'm able to verify the pixel that has the output problem because the rest of the string after it starts functioning again. I've only had one problem where this method didn't work, where the last pixel just stayed on all the time and nothing after it would work. I think it might have had a short in the data output... I just replaced it and got the string working again. Anyway, the straight-pin / clip lead jumper trick kept me from replacing the wrong pixel almost every time. The pins made such small holes that the insulation would pretty much close up when it was removed, although a dot of super glue gel or something like that would be sure to seal the hole if need be.

@OptykMuse could you show a picture of this pin thing, I can't make sense of it, but I'm curious.

Sent from my SM-N960U using Tapatalk


Reply
OptykMuse
Posts: 180
(@optykmuse)
Estimable Member
Joined: 15 years ago

Sorry for the delay... you know how busy this time of the holiday gets 🙂

Here's a pic of one of the bad pixels I was troubleshooting using the straight-pin data bypass method. In this case (as in mos I came across) I bridged across the last pixel to light and function in the string so I knew data was at least getting to that one. If the bridge caused the rest of the string to begin functioning properly I knew the bridged pixel had no data output and needed to be replaced.

20231019 131210

You can see the pins piercing the center conductor (data line) on each side of the pebble pixel, so the data could continue on past it with the clip lead in place. You do need to be VERY careful you don't short to either the power or ground wires while poking it through the data wire insulation. I needed magnification to do this with my old eyes. 🙂


Reply
Posts: 34
(@fabiousa7)
Eminent Member
Joined: 11 years ago

Ohhhhhh I see, that's clever!

Thank you for sharing.

Sent from my SM-N960U using Tapatalk


Reply
Page 3 / 6
Share: