Pixel Power Injecti...
 
Notifications
Clear all

Pixel Power Injection

96 Posts
23 Users
0 Reactions
30.5 K Views
Posts: 2168
(@djulien)
Noble Member
Joined: 19 years ago
dsmjuggalo wrote:I was able to get 500ft of white cat3 cable today for $6.

Where did you find that? Do you have a link for it?

don


Reply
dsmjuggalo
Posts: 663
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

It was local. We have a place called bargain hunt, every couple weeks they lower the price by 10%. They have 4 spools of 250 ft marked at 13.99. I decided to wait it out. Well today they only had 2 spools and they were 80% off so I grabbed both of them. I was able to get 1000 ft of blue cat5e for 5 bucks a couple months ago.


Reply
Posts: 2229
(@plasmadrive)
Famed Member
Joined: 15 years ago
dsmjuggalo wrote:It's actually 24, doubled up is about equal to 21 gauge

According to the calculator I used, with dual 24 gauge wires in parallel running 10 feet at 3 amps and 5 vdc, you will drop 15.4% of the voltage.


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
dsmjuggalo wrote:Just a quick question that's related to power injection. I was able to get 500ft of white cat3 cable today for $6. Since I'm building my pixicles with white 2811 12v nodes I thought it would be great to use this for power injection so it'll blend in. My question is, about how many pixels would be the limit to run injection for if I split the 2 pairs up and used 2 wires for + and 2 for -? I'm wanting to run 100 pixels on each 682 output and inject power at the end of it.

I would never even consider that for power injection under any circumstances.


Reply
Posts: 11
(@schobes)
Active Member
Joined: 12 years ago
szaske wrote:Okay, here is a drawing that shows your suggestion.

Just so anyone else following this thread might find it useful.

-=Steve

In this example how are you able to use a single 5v 300w power supply for half the board (which is needed to power 800 pixels)? I thought each of the two power inputs on the e682 had 32 amp capacity. If you loop a 100ct string back around to the channel output, wouldn't you need all 60 amps of the power supply?


Reply
Posts: 654
(@szaske)
Noble Member
Joined: 14 years ago
Schobes wrote:In this example how are you able to use a single 5v 300w power supply for half the board (which is needed to power 800 pixels)? I thought each of the two power inputs on the e682 had 32 amp capacity. If you loop a 100ct string back around to the channel output, wouldn't you need all 60 amps of the power supply?

I'm not sure I understand your question. The E682 controller does not require 2 power supplies. You can easily connect one supply to both. I think the only reason Jim included 2 power connectors was to give you the ability to split the board into 5V and 12V sides.

BTW, I also drive my whole pixel matrix 1491 pixels using one standard 350W 5V power supply. I don't remember the math behind it, but it ran fine last year. The PS fan comes on a lot more when it's fully lit though :).

-=Steve


Reply
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago

Like Steve, I run a single 5v PS through my e682 for my 1460 pixel matrix with no issues.

Short and badly typed since written from my phone...


Reply
Posts: 11
(@schobes)
Active Member
Joined: 12 years ago
szaske wrote:I'm not sure I understand your question. The E682 controller does not require 2 power supplies. You can easily connect one supply to both. I think the only reason Jim included 2 power connectors was to give you the ability to split the board into 5V and 12V sides.

BTW, I also drive my whole pixel matrix 1491 pixels using one standard 350W 5V power supply. I don't remember the math behind it, but it ran fine last year. The PS fan comes on a lot more when it's fully lit though :).

-=Steve

I plan to run one 5v 300watt supply but was under the impression that each side of the e682 can only handle 30 amps. If you're running 16 50ct strings on a side, how are you powering them? 16 strings equals about 48 amps, but each power input is rated at 30 amps, right?

The example diagram shows 2 50ct strings tied together and powered from the same output by connecting the end of the string back to the beginning.

Make sense?


Reply
Posts: 672
(@pixelpuppy)
Honorable Member
Joined: 12 years ago
Schobes wrote:I plan to run one 5v 300watt supply but was under the impression that each side of the e682 can only handle 30 amps. If you're running 16 50ct strings on a side, how are you powering them? 16 strings equals about 48 amps, but each power input is rated at 30 amps, right?

You still feed power to both sides of the E682 but you take both feeds off the same power supply


Reply
Posts: 11
(@schobes)
Active Member
Joined: 12 years ago
pixelpuppy wrote:You still feed power to both sides of the E682 but you take both feeds off the same power supply

I must be missing something obvious. Let me try this again.

Currently I have 32 50ct strings, 2 5v 300w power supplies, and 2 e682 controllers for my tree. Originally I was just going to run 16 strings in each controller with a single 300w supply.

But earlier in this thread it was recommended to run all 32 strings on a single controller by making 16 strings of 100 and connecting the end of the string back around to the same output channel (see this diagram - http://doityourselfchristmas.com/forums/attachment.php?attachmentid=22774 ).

One power supply is 60 amps. 32 strings of 50 (1600 pixels) is 96 amps. So I still need 2 power supplies. How can you connect two 60 amp supplies to a single e682? Aren't the power inputs limited to around 30 amps per side?


Reply
Page 9 / 10
Share: