Yes you may.
Sent from my SCH-I545 using Tapatalk
I am just getting started with Pixels. This year I am starting with a small project, I just ordered an E6804, and next week I am going to order some pixels. I am not sure how many strings of 50 pixels I am going to start out with, or what type of project that I am going to apply them to. The only decision that I have made is that I am not buying any more regular lights. All of my future projects will be Pixel based.
I really glad I found this post, I have decided to use 5v pixels, so I am going to need to inject power. I understand why, and where. I am still a little fuzzy on how. Can I inject power to 12 strings with only one power supple? Or will I need multiple power supplies? Can I power a 1600 pixel 10' mega tree (32 strings of 5v 50 pixel, I am think ws2811) from a single power supply?
Thanks
John
HydroWVU wrote:I am just getting started with Pixels. This year I am starting with a small project, I just ordered an E6804, and next week I am going to order some pixels. I am not sure how many strings of 50 pixels I am going to start out with, or what type of project that I am going to apply them to. The only decision that I have made is that I am not buying any more regular lights. All of my future projects will be Pixel based.I really glad I found this post, I have decided to use 5v pixels, so I am going to need to inject power. I understand why, and where. I am still a little fuzzy on how. Can I inject power to 12 strings with only one power supple? Or will I need multiple power supplies? Can I power a 1600 pixel 10' mega tree (32 strings of 5v 50 pixel, I am think ws2811) from a single power supply?
Thanks
John
I too am getting started (so my comments should be taken with a grain of salt), but the way I think about it is that 50 pixels is ~3A if they are all on white (worst case scenario). So at 5V, 3A is 15W. You then need to consider any loss in your cables (especially from your power supply to the lights if you are planning a longer run) and the cable thickness. Then lastly, if you are using a power supply that is 5V and 350W say, you wouldn't want to load it more than 80%, so 280W worth, or ~19 strings of 50ct lights (if there are no losses in your wires or otherwise).
I think that people plan on there being 15% loss in their wires, so that 15W/50ct. becomes 17.25W. Which brings that total I mentioned above down to ~16 strings of 50ct. lights with plenty of overhead to be safe.
Hopefully I am not too far off base here and someone can correct me if I am.
Looks good to me . So if John used 3a strings and 350 watt supplies he would need two for his 32 strings. Note that this is good planning but take test measurements after you get the parts and put things together to make sure.
Sent from my SCH-I545 using Tapatalk
Extensions and wire will be the killer here, you may support 16 strings per power supply under optimum conditions but in reality once you add in extensions and so forth this number may go down. I am working on a calculator to show losses for pixel length and extensions, have it close but want to tune it a bit better just yet before I throw it out there.
It is very surprising when you factor in wire losses how significant they are, especially with long runs of pixels on #18AWG wire, or using #18 or #16AWG extensions. So depending on your display 16 might work per supply but it depends on your set-up, how far away you are from the controller, the gauge of wire you use for extensions, line losses in pixel string wiring etc. It does make some sense though having 2- 50 count strings per output on an E682 for example using 2 power supplies, where you get killed is trying to run that same set-up on an E6804 where you have 4x the strings on an output with a single power supply on the controller, so huge line losses for all of the wiring. Definitely another + for justifying an E682 instead of an E6804.
That makes perfect sense... And much to my own embarrassment I do remember reading about capacity planning and the %80 rule. I just didn't put two and two together. This is one of those head slapping I should've had a V8 moments.
Electrified3 wrote:Extensions and wire will be the killer here, you may support 16 strings per power supply under optimum conditions but in reality once you add in extensions and so forth this number may go down. I am working on a calculator to show losses for pixel length and extensions, have it close but want to tune it a bit better just yet before I throw it out there.It is very surprising when you factor in wire losses how significant they are, especially with long runs of pixels on #18AWG wire, or using #18 or #16AWG extensions. So depending on your display 16 might work per supply but it depends on your set-up, how far away you are from the controller, the gauge of wire you use for extensions, line losses in pixel string wiring etc. It does make some sense though having 2- 50 count strings per output on an E682 for example using 2 power supplies, where you get killed is trying to run that same set-up on an E6804 where you have 4x the strings on an output with a single power supply on the controller, so huge line losses for all of the wiring. Definitely another + for justifying an E682 instead of an E6804.
Agreed, I didn't stress the extension issue as much as I should have in my response, but it is a problem to keep in the back of your mind. Also, something to remember is that the voltage drop is twice the length. This is because you will get a drop on the voltage line, as well as the common return. So if you are working the problem out on an online calculator (until your new one is released), and you have a 15ft run, you will want to calculate the loss at 30 ft (15ft out, and 15ft back).
A new calculator sounds great, I can't want to see/use it!
If you have a centralized control box, and you need to run a line out 15ft. (I found a voltage drop calc on-line) if you use 18awg you will drop to 4.7 Volts then you add on the volt drop for the pixel string itself... assuming 5 meters, you are down to 4.4 V after 15ft, plus 50 pixels. Does this sound right so far? LEDs need ~3.4v (Correct?). Is it when you voltage drops below 3.4 that you need to inject power? How do you compensate for the initial voltage drop?
One more question: What is the voltage coming out of each of the bridge connection? Do you have any problems splitting one connection coming out of the power supply 13 or 15 ways?
Thanks
John
I would do a bit of reading on voltage drop, if you look at the wiki in here they have some good info on voltage drop.
http://www.doityourselfchristmas.com/wiki/index.php?title=Power_Injection
Once you fall from 5V to 4.75V you will start to see the end dimmer than the start of the string, you will see substantial loss below 4.5VDC. You will be surprised how quickly the voltage drop changes by the gauge of wire your use. Going from an #18AWG extension to a #12AWG will be dramatically different.
There are calculators to figure this out but you need to be sure to account for everything. You may have a #14 extension but your pixel string wiring is #18. So if you had 50 pixels with 4 3/4" spacing that is alot of wire, 4 3/4 * 50 * 2 for the pixel wiring multiplied by the wire resistance and then by the amp draw of the circuit, then 15 x 2 for the extension multiplied by the wire resistance and then by the amp draw of the circuit. You also need to know the amp draw of the circuit to determine the voltage loss. It gets a bit complicated and this is just a single run, if you inject power from the same feed to the start of the string then the calculation gets a bit more complex and you need to apply Kirschoffs law to determine the branch circuits load then apply that to the entire length to determine voltage loss.
Regardless, you don't want to have 3.4 volts driving your pixels, that will be very obvious, between 4.5 and 4.75 should be manageable, above 4.75 should be no issue. If you use a better power supply sometimes you can boost the output slightly to 5.2 or 5.4V which will give you a bit more room for voltage drop as well.
I am complete newbie when it comes to electricity thanks for your patience in answering my questions.
What gauge wire do you run from your controller to you pixel strings. I was thinking 18awg would be a nice balance between cost and voltage performance.
Thanks
John
Sent from my iPad using Tapatalk HD
