Pixel Power Injecti...
 
Notifications
Clear all

Pixel Power Injection

96 Posts
23 Users
0 Reactions
30.5 K Views
Posts: 2229
(@plasmadrive)
Famed Member
Joined: 15 years ago
duramadmax wrote:You are correct and I see what you are saying. This was a quick fix for me this year. I will probably due the correct option 2 design for next year with the extra ground wire.

See I did not have my EE101 hat on like I should have. Had my Dunce cap on instead. It happens when you have someone saying, "you not done yet!!"

LMAO!!! :w00t:


Reply
Posts: 2229
(@plasmadrive)
Famed Member
Joined: 15 years ago

One more thing I forgot to mention about the Plasma Icicles and the power arrangement. Since I used 24vdc main supplies that are good for 10 amps, I used #14 wire which is good for 15 amps. From there I used about 20 or so DC-DC converters. Each converter has it's own internal protection for overloads and short circuits. So basically I had branch circuit protection at each converter. I had no need for fuses and everything was designed to carry the available current, so I was very comfortable with the arrangement.

The bottom line is that protection is one more benefit of converters.


Reply
Posts: 654
(@szaske)
Noble Member
Joined: 14 years ago

After reading this thread here is how I plan to inject power into my pixel strip. I'm going to inject power at the end of the line. Here is a drawing of what I plan to do.

power injection

-=Steve


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
szaske wrote:After reading this thread here is how I plan to inject power into my pixel strip. I'm going to inject power at the end of the line. Here is a drawing of what I plan to do.

-=Steve

Be sure to fuse the end being supplied from the power supply, as you have it there is no protection and have full potential of the supply to the string in the event of a short.


Reply
Posts: 654
(@szaske)
Noble Member
Joined: 14 years ago

Alternatively, if I want to make an even longer length of pixel strip, I can inject in the middle of the line using a t intersection. Here is a drawing of that.

power injection long

A few questions about this setup.

1. One thing that will become a problem is that in the standard CG1500 enclosure there is really not a lot of space to have a lot of wires connected to those 5v rails. I like the idea of having one of those distribution splitters that Electrified3 showed in his pictures. What is the best kind of splitter to get?

2. How many pixels does can each port support on a E682? I'm guessing I cannot connect a whole matrix to one port on the E682 controller.

-=Steve


Reply
Posts: 654
(@szaske)
Noble Member
Joined: 14 years ago
Electrified3 wrote:Be sure to fuse the end being supplied from the power supply, as you have it there is no protection and have full potential of the supply to the string in the event of a short.

How would I do that? I believe you said I could instead connect to the E682, but then I'd be using a port. And those things come in short supply. Does someone make a fused cable, or easy part that I can add to a cable?

-=Steve


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago

Just connect the end to the same port on your E682 that you start the string with, just connect the +5VDC and Common and not the data line to the end. So in your example on port 4-4 you will have 2 wires on the positive terminal, 1 on the data and 2 on the common, now it is protected by the on board fuse. No need for anything special or extra fusing.


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
szaske wrote:Alternatively, if I want to make an even longer length of pixel strip, I can inject in the middle of the line using a t intersection. Here is a drawing of that.

A few questions about this setup.

1. One thing that will become a problem is that in the standard CG1500 enclosure there is really not a lot of space to have a lot of wires connected to those 5v rails. I like the idea of having one of those distribution splitters that Electrified3 showed in his pictures. What is the best kind of splitter to get?

2. How many pixels does can each port support on a E682? I'm guessing I cannot connect a whole matrix to one port on the E682 controller.

-=Steve

At 165 pixels I would think injecting just at the end will work fine. In the examples I was doing I had 200 pixels and injecting just at the end corrected it. Of course you would need to try it for yourself to confirm, the type of pixels, your connections, length of any extensions will all play a role in it. Best to test first and see what your limits are with your hardware.

What I used in mine was terminal blocks, there are all kinds, many companies make them. Here is a link to the Grainger website terminals.
http://www.grainger.com/category/terminal-blocks/terminal-blocks/electrical/ecatalog/N-8h9
You need to buy as many terminals as you need and also a piece of DIN rail for them to clip on to. The rail connects to your enclosure, the terminals snap on to it. Be cautious, make sure the rail you buy is the right one for the terminals you use, there are different types and styles, DIN is the most common though.


Reply
Posts: 654
(@szaske)
Noble Member
Joined: 14 years ago
Electrified3 wrote:Just connect the end to the same port on your E682 that you start the string with, just connect the +5VDC and Common and not the data line to the end. So in your example on port 4-4 you will have 2 wires on the positive terminal, 1 on the data and 2 on the common, now it is protected by the on board fuse. No need for anything special or extra fusing.

Okay, here is a drawing that shows your suggestion.

power injection v2

Just so anyone else following this thread might find it useful.

-=Steve


Reply
Posts: 752
(@popo-b-trippin)
Prominent Member
Joined: 13 years ago
szaske wrote:Okay, here is a drawing that shows your suggestion.

Just so anyone else following this thread might find it useful.

-=Steve

Does anybody know if you can do this type of injection with the PX1 (where you simply add the +5VDC and Common from the controller to the end of the pixel run), or would that be putting too much on the PX1?


Reply
Page 6 / 10
Share: