Pixel Power Injecti...
 
Notifications
Clear all

Pixel Power Injection

96 Posts
23 Users
0 Reactions
30.5 K Views
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago
angus40 wrote:When I designed my matrix ,I used the 1/2 welded wire building mesh . this allowed me the flexibility to vary my spacing > expand my pixel count and provide
an excellent structure to support the pixels .

As a bonus this matrix is light weight and easily storable.

For 2013 I used a spacing of 3" x 3" for a 43 x 11 pixel count . I will be adding another 450 pixels for 2014 installing them in an offset alignment

that will add greatly for graphics resolution.

I've considered the wire mesh as well since it would be WAY less work, but I would still need something behind it to block ambient light since this will be at the end of a street and not against a house. Are you using round or square?

Also, when you say an offset alignment. You mean that one matrix will be staggered with the other? Meaning that the second matrix (for instance) will end up having a pixel in between the pixels on the first matrix? If so, nutcracker can handle that?


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Black coro is what I used for a backing. I wrapped my wood frame 1 x 4 external frame and 1 x 2 internal supports with black poly before assembly<

yes the internal matrix is as you described , I have no clue about nutcracker as I use HLS because it is a sequencer and has complete discrete control .

Also HLS enables users the ability to export .png files of native effects as well as foreign ( nutcracker ) effects for easy customization in alternative software

and to be imported back into HLS.

With these capabilities , optimum matrix control is just that ez 🙂

Cheers


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago

After using both E6804's and E682's I would highly suggest you use the E682 in a matrix to simplify your connections and eliminate the possibility of needing any injection on your matrix at its starting size.

The first one I built I used ABS pipe to make a frame and mounter 30/M led strips spaced 1 1/2". So mine was/is 150 x 22, It looked great but was a nightmare to handle as it was 16' long and 4' wide. It didn't last long though, hard to attach the strings to the ABS, I only had a vertical piece every 12" so it didn't take long for it to start to droop in between the supports, then a few start touching it, wind started blowing hard and poof, it was a mess.

I only had mine running for about a week, then ended up with a mess so took it down. I am in the process of rebuilding that one now, I have a local shop using their CNC to make 2 custom panels, with dado cuts for the strips to lay into. I am also cutting out 1"x14" sections in between the rows so the wind can blow through it, where I live we get some nasty winds off of the lake, so don't want a big sail out there. I am making it in 2 pieces this time, 4' x 8' so it will be easier to handle then will just put a frame to connect them or have it able to pivot and have a 2 sided pixel board as well.

I am also playing with a smaller one now to use as a face for wire frame snowmen, but using 2811 bullet pixels. I am looking at using polypropylene "pegboard" just drilling out the holes to the size of the pixel so the grid pattern spacing is already there. http://www.homedepot.com/p/Triton-DuraBoard-3-16-in-Hole-White-Polypropylene-Pegboards-22-in-W-x-18-in-H-2-Pack-018/204774898#

Just pixels add up quickly spaced that closely, like a 22" x 18" spaced 1"x1" will end up almost 400 pixels which makes me lean back toward strips, but I have alot of bullet strings hanging around to try with that first.


Reply
Posts: 2229
(@plasmadrive)
Famed Member
Joined: 15 years ago
Electrified3 wrote:
....... Good planning at the start will save you alot of work later!

Truer words were never spoken!


Reply
Posts: 654
(@szaske)
Noble Member
Joined: 14 years ago

I'm thinking I'd use what I have in the past. Check this out.

happyh

I made this with rope lighting. The surface is just some heavy duty plastic fencing that I bought at HomeDepot, but I like that it is very transparent. It's zip tied to 3/4" pipe, which for some reason is super cheap at Home Depot (it's like $2 for a 8' section, and very rigid). It's about 90" wide.

-=Steve


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
szaske wrote:I'm thinking I'd use what I have in the past. Check this out.

I made this with rope lighting. The surface is just some heavy duty plastic fencing that I bought at HomeDepot, but I like that it is very transparent. It's zip tied to 3/4" pipe, which for some reason is super cheap at Home Depot (it's like $2 for a 8' section, and very rigid). It's about 90" wide.

-=Steve

Nice Job!

One thing to note using pixels to generate a matrix even spacing is very important both vertically and horizontally. Using the same set up with pixels using a bazillion wire ties I think could work. Nice part with that is you might have double sided viewing, text would be backwards and so forth, the front side would be the best of course but something would show up on the other side as well.


Reply
Posts: 389
(@jcross)
Reputable Member
Joined: 15 years ago

I am not suggesting that this is the correct way of wiring things, however, this is how I wired my display this year (power injection) and it worked very well.

Pixel Wiring Diagram

EDIT: In the interest of Safety I have added fuses to the diagram and changed the injection method to what I believe most people will be doing. Sorry I deleted the old version so it wouldn't be confused, but this broke a few future links in this thread.


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
jcross wrote:I am not suggesting that this is the correct way of wiring things, however, this is how I wired my display this year (power injection) and it worked very well.

Thanks Jason, good to see how others do this as well.

Just one question, your injection lines, did you fuse them? I ask because I did have an oops with a piece of #12AWG from an injection line go up in smoke on me without fusing off of a 300W 5V power supply. I was shocked to see how much current that low voltage power supply will put out in a short condition and be able to sustain it, mine kept burning until I managed to get the plug pulled. Learned my lesson from that and if I use power injection from any other source than it's output I fuse it. If you tied your injection lines to the same 5VDC and Common from your control output it will be protected by the onboard fuse and the issue is resolved, otherwise always be sure to put a fuse in your injection line, it seriously could be a fire hazard without it.


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

So in that diagram, you are not using power from the E682 at all? Just using the PS directly to power the pixels? Any reason to not use the E682 for 1st 2 50 count of pixels? Just curious....
I ask as I have no pixels as of yet and trying to get a handle on injection for the strips I have ordered.
Thanks.


Reply
Electrified3
Posts: 716
Topic starter
(@electrified3)
Prominent Member
Joined: 13 years ago
DrNeutron wrote:So in that diagram, you are not using power from the E682 at all? Just using the PS directly to power the pixels? Any reason to not use the E682 for 1st 2 50 count of pixels? Just curious....
I ask as I have no pixels as of yet and trying to get a handle on injection for the strips I have ordered.
Thanks.

That can be done, but you need to be sure to fuse them from the power supply, if taking the power from the board it has its fusing there.


Reply
Page 4 / 10
Share: