The one thing I've been wondering as I get into this arena (for piece will be a pixel matrix), is about the most efficient way to inject more power. If we assume I am using a 5V string (I am ignoring 12V for now), I know a lot of people like to inject every 50 pixels. In my mind, since my matrix will be something like 50 wide by 13 tall, the best way for me to do this is to inject power on the 25th pixel, 75th, etc. (as opposed to the 1st, 51st, etc). This way I can just run the power down the middle of the matrix and the most the voltage needs to travel is 25 pixels in either direction.
Am I off my rocker in this thinking?
Thanks for the writeup/pics, very informative!
A question I have as well is let's say you want to inject between two strings that have a male and female end already preinstalled on them (i.e. Pixabulbs). Can you create an "injection pigtail" that is made up of a male and female connector? I was considering soldering the data lines together and then soldering the Positives together and negatives together from the two connectors (3 wire combo). This should create a good solid connection between the connectors but to get power to the "injection pigtail" I wanted to run heavy gauge landscape wire from my power source and connect to the "injection pigtail" with either spades or waterproof nuts twists. I am doing a large scale matrix on my house and will have some lengths to go so that is why I was considering this. I think it is a cheaper way to go than with Ts and extension cables. Any thoughts?
toozie21 wrote:The one thing I've been wondering as I get into this arena (for piece will be a pixel matrix), is about the most efficient way to inject more power. If we assume I am using a 5V string (I am ignoring 12V for now), I know a lot of people like to inject every 50 pixels. In my mind, since my matrix will be something like 50 wide by 13 tall, the best way for me to do this is to inject power on the 25th pixel, 75th, etc. (as opposed to the 1st, 51st, etc). This way I can just run the power down the middle of the matrix and the most the voltage needs to travel is 25 pixels in either direction.Am I off my rocker in this thinking?
Thanks for the writeup/pics, very informative!
I was starting to write "That sounds like it might be an excellent method but only if you kept the 13 strings separate and not in series. Most likely though you will want to connect at least three of the strings together to maximize the use of your controller's outputs." but as I was typing I was thinking. I don't know why you couldn't connect the data and ground lines in series and inject (connect) the power and ground feeds in the middle of the strings. The only possible issue is that might create a ground loop which could cause issues with the data.
The thought I had on powering my strings is to run a 14 gauge pair to each end of the pixel matrix creating double ended power feed busses. I'd then parallel the pixel strings power and ground connections to these busses but I think the split-50 feed method is well worth trying.
OriginalHotrodder wrote:I was starting to write "That sounds like it might be an excellent method but only if you kept the 13 strings separate and not in series. Most likely though you will want to connect at least three of the strings together to maximize the use of your controller's outputs." but as I was typing I was thinking. I don't know why you couldn't connect the data and ground lines in series and inject (connect) the power and ground feeds in the middle of the strings. The only possible issue is that might create a ground loop which could cause issues with the data.
The thought I had on powering my strings is to run a 14 gauge pair to each end of the pixel matrix creating double ended power feed busses. I'd then parallel the pixel strings power and ground connections to these busses but I think the split-50 feed method is well worth trying.
ON the Plasma Icicles I ran 150 pixels per universe. I injected power in between ever set of 60 pixels. That way no more than 30 pixels were in a power string... but the data carried thru from 1-150. You just have to make sure you tie all commons together. If you are using the same supply on all of them and not injecting via DC-DC converters or extra power supplies, you can actually just leave the entire string connected, power and data, and inject the + and - at any point along the line.. it would be just paralleling the power from the same supply.... there would be no issue with multiple supplies fighting each other. However, you will still experience some drop in the power wires from the supply to the injection point.. Bigger wire will yield less drop..
Using the converters lets you inject at many points without the Vdrop issue being a problem... again, common must remain intact all the way thru.. You would just split the + line for the power injection.
pythan wrote:ON the Plasma Icicles I ran 150 pixels per universe. I injected power in between ever set of 60 pixels. That way no more than 30 pixels were in a power string... but the data carried thru from 1-150. You just have to make sure you tie all commons together. If you are using the same supply on all of them and not injecting via DC-DC converters or extra power supplies, you can actually just leave the entire string connected, power and data, and inject the + and - at any point along the line.. it would be just paralleling the power from the same supply.... there would be no issue with multiple supplies fight each other. However, you will still experience some drop in the power wires from the supply to the injection point.. Bigger wire will yield less drop..Using the converters lets you inject at many points without the Vdrop issue being a problem... again, common must remain intact all the way thru.. You would just split the + line for the power injection.
Excellent! That will make the power injection much easier, one connection in the middle of each string (of 50) instead of one at both ends. Thanks
OK, sounds like others are roughly on the same page with my thought process, that will be my plan then. I don't see why it should be a problem (if like was pointed out, we are using just one power supply), so unless someone comes up with a good reason not to, I will probably do that.
One caveat:
I would feed power to the first pixel where the data is fed to the string. That way you will not have ground loop issues. As well there are other issues that I won't go into.. none of them for sure but always possible. So do that one thing and you should be golden.
In reality if only using a 50 x 13 matrix I would just use an E682 or a controller with enough outputs to run your matrix and wire each row to an output on one end and no injection required, fast refresh rates, no fusing concerns, just works out to a much cleaner install. The E682 would even have a few channels left over for you since your matrix will only occupy 650 out of 2040 possible.
I will bet though, after you do that one, the next year you will want 50 x 26 or 100 x 26 or 100 x 52, then you will have to add injection or controllers.
Have you decided on any pixel type or spacing? How about row spacing? What would you like to display? Test, effects, graphics? What distance will you want it visible from? How will you support it and maintain the pixel spacing? These I find are the most important issues as well as having a plan to be able to expand without having to start over. These have been a thorn for me in my experience so far with a matrix. Good planning at the start will save you alot of work later!
Electrified3 wrote:In reality if only using a 50 x 13 matrix I would just use an E682 or a controller with enough outputs to run your matrix and wire each row to an output on one end and no injection required, fast refresh rates, no fusing concerns, just works out to a much cleaner install. The E682 would even have a few channels left over for you since your matrix will only occupy 650 out of 2040 possible.I will bet though, after you do that one, the next year you will want 50 x 26 or 100 x 26 or 100 x 52, then you will have to add injection or controllers.
Have you decided on any pixel type or spacing? How about row spacing? What would you like to display? Test, effects, graphics? What distance will you want it visible from? How will you support it and maintain the pixel spacing? These I find are the most important issues as well as having a plan to be able to expand without having to start over. These have been a thorn for me in my experience so far with a matrix. Good planning at the start will save you alot of work later!
I'm looking into using the E6804. As you point out, it is overkill for this, but I am thinking that if I can get my wife to not noticed how much I am spending this first go round (since I am starting from nil), adding to the matrix and/or doing something new will be more of a breeze in the future.
Right now I am leaning towards the TLS3001 variety. I know they are 5V (which is a big no-no for a lot of people), but since it will just be in a matrix, I can pretty easily run more power to them and they will all be in the same location. I am going to do a 2" spacing (vert and horiz) so that I can pretty closely get back to 24"x12" digits which is what I had in my old PIC driven incandescent countdown to christmas. I was hoping to have every up on the screen at once, but now I think I am going to scroll it so the numbers can be big. I guess I will also do some effects and/or simple graphics once in a while on it to spice things up since I have all those pixels to play with (might as well do something with them while it counts down for 2 months 24hrs a day). The viewer will probably be ~15ft away since it gets installed at the end of a dead-end and most people drive down the street and stop to look at the old sign. Still working out how to support the pixel spacing (been talking to hotrodder about that some), but I am currently leaning towards drilled wood with the pixel poking through, all that finished off with some sort of framing to keep everything straight and support it. But with all these things, I am still trying to plan it out also (I do months of planning and still never feel 100% confident).
Do you have anything posted online about your matrix? I'm always looking to learn.
When I designed my matrix ,I used the 1/2 welded wire building mesh . this allowed me the flexibility to vary my spacing > expand my pixel count and provide
an excellent structure to support the pixels .
As a bonus this matrix is light weight and easily storable.
For 2013 I used a spacing of 3" x 3" for a 43 x 11 pixel count . I will be adding another 450 pixels for 2014 installing them in an offset alignment
that will add greatly for graphics resolution.
