Hi All -
Having lots of pixel flickering issues with my just built matrix. Pixels flicker randomly, across all rows, whenever the controller is powered on and idle. By flicker I mean they flash on/off quickly in either red, blue or green. In test mode or running a sequence the flickering is whole rows/sections at a time and is much worse.
My matrix has 31 rows of 45 pixels controlled by a Falcon expansion board tied to a F16V3. I have two HolidayCoro 5V power supplies for the pixels and expansion board and two HolidayCoro 12V power supplies for the F16V3 (and for other pixels).
The power and ground for the pixels are direct from the power supplies, bypassing the controller outputs. Only the data is wired through the outputs. The pixels are wired in strings of 90, with power injection at both ends. I have all the grounds from the power supplies tied together. A diagram is attached showing how one section (of four) of my matrix is wired.
I didn't notice any flickering or other issues when I first tested the individual strings (50 pixels @ 5 volts) before I added them to the matrix.
I've tried various things to isolate the cause and nothing seemed to resolve it until I temporarily switched one group of pixels from a HolidayCoro waterproof power supply to a Meanwell LRS-350-5. When I did that those pixels had zero issues while the rest continued with the flickering.
Reading through various posts here some have brought up the potential for power loops or susceptibility to interference when power injecting from both ends of a string. Could the Meanwell power supplies just be that better at preventing that interference? Is there a way to resolve this with my HC power supplies (capacitors across power and ground?) or should I switch to the Meanwell power supplies for my matrix and mega-tree (100 pixel strings / power injected each end).
Thanks,
Mike
mtbehnke wrote:Hi All -Having lots of pixel flickering issues with my just built matrix. Pixels flicker randomly, across all rows, whenever the controller is powered on and idle. By flicker I mean they flash on/off quickly in either red, blue or green. In test mode or running a sequence the flickering is whole rows/sections at a time and is much worse.
My matrix has 31 rows of 45 pixels controlled by a Falcon expansion board tied to a F16V3. I have two HolidayCoro 5V power supplies for the pixels and expansion board and two HolidayCoro 12V power supplies for the F16V3 (and for other pixels).
The power and ground for the pixels are direct from the power supplies, bypassing the controller outputs. Only the data is wired through the outputs. The pixels are wired in strings of 90, with power injection at both ends. I have all the grounds from the power supplies tied together. A diagram is attached showing how one section (of four) of my matrix is wired.
I didn't notice any flickering or other issues when I first tested the individual strings (50 pixels @ 5 volts) before I added them to the matrix.
I've tried various things to isolate the cause and nothing seemed to resolve it until I temporarily switched one group of pixels from a HolidayCoro waterproof power supply to a Meanwell LRS-350-5. When I did that those pixels had zero issues while the rest continued with the flickering.
Reading through various posts here some have brought up the potential for power loops or susceptibility to interference when power injecting from both ends of a string. Could the Meanwell power supplies just be that better at preventing that interference? Is there a way to resolve this with my HC power supplies (capacitors across power and ground?) or should I switch to the Meanwell power supplies for my matrix and mega-tree (100 pixel strings / power injected each end).
Thanks,
Mike
If you have the power set to 12 volts lower it. Try 11.8 volts. I've had issues in the past and lowering the output voltage cleared it up.
Sent from my SM-T710 using Tapatalk
pmiller wrote:If you have the power set to 12 volts lower it. Try 11.8 volts. I've had issues in the past and lowering the output voltage cleared it up.
Aside from them being 5V pixels, that's actually why I bought the Meanwell; the HC power supplies don't have a way to adjust the voltage and I wanted a power supply that would let me reduce the voltage to test out if overvoltage could be part of the cause.
What's more interesting is the MW had a slightly higher voltage out of the box (5.088V) and has no flickering issues. The HC ones are at 4.970V and 5.045V and do have flickering.
did you buy the rainproof power supplies from HC?
TazChaLet wrote:did you buy the rainproof power supplies from HC?
Yes.

