Nutcracker set up
 
Notifications
Clear all

Nutcracker set up

10 Posts
3 Users
0 Reactions
4,188 Views
Posts: 213
(@aaron1)
Estimable Member
Joined: 16 years ago
Electrified3 wrote:Terry, do yourself a favour and just set it to 12 universes 510 channels so you assign all of your capability of the controller running unicast.

For the megatree, it appears he plans to use 42 pixels per output, with each cluster forming a universe. If he sets xlights up to use 12 universes of 510 channels, he'll have to do more manual channel entry for his megatree. Using the 504-channel universe for his megatree will keep him from having to change the channels manually in the model setup. I did it this way this past year. I actually used 3 strands of 56 each (also comes to 168 pixels, or 504 channels). Saved me some time setting up my model. Otherwise, he'll have to manually enter the start/end addresses for strings 5-24 of his megatree.

Since he's not going to be fully loading the e682, it probably doesn't matter.

Just my $.02.


Reply
Electrified3
Posts: 716
(@electrified3)
Prominent Member
Joined: 13 years ago
aaron1 wrote:For the megatree, it appears he plans to use 42 pixels per output, with each cluster forming a universe. If he sets xlights up to use 12 universes of 510 channels, he'll have to do more manual channel entry for his megatree. Using the 504-channel universe for his megatree will keep him from having to change the channels manually in the model setup. I did it this way this past year. I actually used 3 strands of 56 each (also comes to 168 pixels, or 504 channels). Saved me some time setting up my model. Otherwise, he'll have to manually enter the start/end addresses for strings 5-24 of his megatree.

Since he's not going to be fully loading the e682, it probably doesn't matter.

Just my $.02.

Why would you need that addressing in Xlights to correct your tree addressing, you completely lost me there. In this setup it looks like you have configured a total of 3777 channels out of a potential 6120, so you have another 2343 channels that you have tossed out? Seems like you are pigeon holing yourself for no reason? Logically I think I see what you are doing, aligning yourself for a single strand per output of the E682 but that is completely controlled by the E682 configuration absolutely nothing to do with XLights configuration.

Set you controller in XLights for its full capability, 12 universes, 510 channels per universe, set mega tree model to start at ch1, 24 strings, 42 pixels. Now you need to know how you will wire your lights to your controller to determine your E682 set up. The controller setup in XLights should have no effect on your model setup. The configuration of the E682 will have an effect on your model set up.

So as I said, set your board for full potential in XLights, then you have it for later if you want to add things in. Like maybe you want to add a star, or another small display later, your current setup would have to be redone if you ever tried to add anything later and typically in the past I have seen you would need to open all of your sequences with the modified channel configuration and re save them to make them work.

The important part with aligning things up is your E682 set up and how you plan to wire them. If you post your E682 to start and an idea of your MT wiring plan we can figure this out quickly.


Reply
Electrified3
Posts: 716
(@electrified3)
Prominent Member
Joined: 13 years ago

See if this helps, here is a screenshot of the XLights setup, I have my IP set different than default.

XLights Controller Setup

Then I would set the E682 something like this, it uses 1-1,1-2,1-3,1-4,2-1,2-2 as outputs to your tree (4 strings of 42 per output), 2-3 & 2-4 are spares, but addressed to be usable later if you like. Then 3-1, 3-2, 3-3, 3-4 all set for 50 pixels on each output, 3 for your arch's and a spare on 3-4 50 pixels long again to add in later if you like. Group 4 is assigned with Renard Protocol to use all 4 ports for Renard output, you need the entire group to use the same protocol or pixel type/voltage.

E682 Setup

Now you have fully occupied your channel capability of your E682, this is just an example for you, if you change grouping in your MT you can free up more outputs, in my example I am showing 4 strings per output, if you change that to 6 per output you end up with Group 2 totally empty. If you groups your arch's you can put 150 out 1 output and have 3 remaining with 150 pixels each on them. I tend to try to stick to groups of 150 to get quick refresh rates myself and limit power injection. There are a million ways to organize it which is why we need to know how you plan to wire it to set up the E682 optimum for your set up. Probably good to sort out how many channels to reserve for group 4 for your Renards then go back and distribute the other groups to utilize things even more efficiently.

Now in XLights models with my example you end up with this for a MT, no custom mapping required, just punch in strings, pixels and start, all is good.

MT Model Setup

Then configure Arch 1, need to figure out what channel universe 8 ch 463 is, looks like 1515 as start.

Arch 1

Now arch 2 add 1 to the end count from arch 1

Arch 2

Same thing for arch 3 add 1 to end count from arch 2, reached limit for attachments, but same as the other 2, end count of arch 2 +1.

See if that makes any sense. You now have it functional for the RGB's, now just a bit of setup for Renards, nothing too hard about the setup, keeps everything in order, extra channels allowed for to add in extras later and so forth. Want to add a 50 count star? Just plug it into port 3-4 and create your model and go, no major changes needed in set up, etc. Want to add 8 more strings to your tree, plug them into 2-3, 2-4 and add 8 strings to your MT model and away you go.


Reply
Electrified3
Posts: 716
(@electrified3)
Prominent Member
Joined: 13 years ago

1 other thing, if you already have your Renards wireless on XBees just keep them that way if you want, you are really are not gaining much by running them on the E682, just burning channels and outputs. Leave the Renards and XBees as is, not sure if you used XLights for them previously, if so leave the set up as it and just add the E1.31 to your setup, forget about group 4 on your E682 and just add it in that way. I have no idea how you would integrate XBees into an output from the E682 anyway. So if that part worked already leave it that way.


Reply
Posts: 213
(@aaron1)
Estimable Member
Joined: 16 years ago
Electrified3 wrote:Why would you need that addressing in Xlights to correct your tree addressing, you completely lost me there. In this setup it looks like you have configured a total of 3777 channels out of a potential 6120, so you have another 2343 channels that you have tossed out? Seems like you are pigeon holing yourself for no reason? Logically I think I see what you are doing, aligning yourself for a single strand per output of the E682 but that is completely controlled by the E682 configuration absolutely nothing to do with XLights configuration.

Set you controller in XLights for its full capability, 12 universes, 510 channels per universe, set mega tree model to start at ch1, 24 strings, 42 pixels. Now you need to know how you will wire your lights to your controller to determine your E682 set up. The controller setup in XLights should have no effect on your model setup. The configuration of the E682 will have an effect on your model set up.

So as I said, set your board for full potential in XLights, then you have it for later if you want to add things in. Like maybe you want to add a star, or another small display later, your current setup would have to be redone if you ever tried to add anything later and typically in the past I have seen you would need to open all of your sequences with the modified channel configuration and re save them to make them work.

The important part with aligning things up is your E682 set up and how you plan to wire them. If you post your E682 to start and an idea of your MT wiring plan we can figure this out quickly.

I see what you're saying about the ability to address them in this way without a bunch of manual entry. I stand corrected on that front. Thanks for pointing out how to pull that off.

Now, it comes down to how he wants to wire things together. Unless he wants strings of 168 pixels each (coincidentally, I used 168-pixel strings this past year, with my 3 56-pixel strings connected end-to-end), he won't (and doesn't necessarily need to) reach the limit of the controller hardware.

FWIW, none of my 4 e682 controllers is "maxed out" on universes (each one consumes about 8 universes, more or less). Some would say that's wasteful. I do it that way because it simplifies the setup in my yard, putting my controllers closer to the elements they control.

At the end of the day, Terry, it's personal preference for you. I stand corrected and Electrified is right about not having a difficult time doing manual addressing on the models. So, his method is totally viable, as is the method you posted above. Electrified's method will even save you the cost of one e682 controller. Probably saves the cost of an enclosure and Ethernet switch as well, depending on the rest of your setup.

Good luck. Looks like you're on the right track, either way.


Reply
Page 2 / 2
Share: