Notifications
Clear all

New GECE pixels

40 Posts
14 Users
0 Reactions
14.9 K Views
Posts: 347
Topic starter
(@dougd)
Reputable Member
Joined: 19 years ago
[#23678]

I just opened my first box of GECE pixels that Lowes carried this year, the 25 count box. First thing I noticed was no remote control. There is now a button on the small green control box. The second thing I noticed was the power supply that was packaged with the lights is now rated at 6 volts, 1.2 amps as opposed to all the lights from last year whether the 36 count or 50 count, those power supply's were all 5 volt at 3 amps.

As anyone used these lights yet? Are the pixels the same as before, hopefully they don't need 6 volts to control them. I sure don't want to keep the new ones separated from the old ones.


39 Replies
Posts: 2128
(@livermore-dad)
Famed Member
Joined: 16 years ago

I run all my GECE's with a 7volt power supply.. And these are 2-3 years old

Tory


Reply
Posts: 347
Topic starter
(@dougd)
Reputable Member
Joined: 19 years ago

That's interesting, did they function better fro you at 7 volts? Are you injecting power?


Reply
Posts: 2128
(@livermore-dad)
Famed Member
Joined: 16 years ago

They seem to work just fine, not injecting, powered via the e681, lengths from 6' almost 50' away. including some runs of almost 10' between pixels. It's white and not pink. I lost 1 pixel (the red is out), but after 2 years, think this is just attrition, vs a power caused failure.

Tory


Reply
Posts: 347
Topic starter
(@dougd)
Reputable Member
Joined: 19 years ago

Thanks Tory for the info. I powered all mine at 5 volts and I had a some of the pink problem you are referring to. I will try some different voltages and see what works. I just hope these new pixels are the same as the old ones. I bought a few of these boxes to replace the pixels that lost a color during this last season. I have about 1500 of these pixels and it looks like about 10 lost a color.


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

I ran all of my GECE's this year at 5V. And I had a few colors go out, so I will be replacing them with some of this year's purchases.

The new ones I bought on clearance had a mixed bag of power = the 20 ct icicles have a 6V power supply, but the 8 count pathway lights have a 5V power supply.


Reply
Posts: 347
Topic starter
(@dougd)
Reputable Member
Joined: 19 years ago

I will have to check the output going out to the pixels and see if its 5 volts or 6 volts.


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

i noticed the same things about this year's differences. Plus a few more: if you bought a GECE snowflake wireframe last year, it didn't have the holographic background, it was just an open wireframe, and it had 48 bulbs instead of this year's 36. (6 in the center, plus one more on each arm)
The controller boxes last year (from the strings that had the remotes) had pads on the board for a pushbutton switch, and if you shorted the pads, it would in fact toggle thru the patterns. I haven't opened up a controller from this year (yet) but i'd bet that the radio daughterboard is no longer there, but the main board is otherwise the same.


Reply
Posts: 347
Topic starter
(@dougd)
Reputable Member
Joined: 19 years ago
Livermore-Dad wrote:I run all my GECE's with a 7volt power supply.. And these are 2-3 years old

Tory

Where did you find a 7 volt power supply.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Hmm - - the GECE Snowflake walkway set (6 of them/string) have a 6v/1.3A supply and a push-button on the controller vs a remote. I guess they assume since these would be lower to the ground it's not a big deal to turn them on manually as opposed to being up on your gutters like the longer strings.


Reply
Page 1 / 4
Share: