New controller box ...
 
Notifications
Clear all

New controller box setup

4 Posts
1 Users
0 Reactions
1,124 Views
Posts: 37
Topic starter
(@tbm878)
Trusted Member
Joined: 9 years ago
[#55892]

This is my new controller box. I spent a lot of time on here researching others setups and took what i thought were their good features and combined them to make my setup. I will have a k40 board powering 6 of these controller boxes with smart differential reciever boards that will use 3 of the 4 channels for the window matrix's, and each will have 1 spare channel for other items/props near by. I know it is a bit over designed, but i like that everything is 1-to-1....1 output channel with 1 psu and 1 power inj board. I am going to make some unistrut L-shaped brackets to hold the 6' x 6' matrixes spaced off the windows approx 8" and the controller boxes will be independently supported behind the matrix panels facing towards the windows. That way if i need to get to the controller boxes i just have to open a window to access them. I bought the biggest & shortest depth bud boxes that i could find (ptq-11072). Then i drew everything up in autocad and played with a couple different arrangements to see how/if it would all fit. And this is the layout that i chose.

20220724 210331 copy 2048x2731
matrix controller box layout

3 Replies
Posts: 37
Topic starter
(@tbm878)
Trusted Member
Joined: 9 years ago

I started with a 4' x 8' x 1/4" sheet of black hdpe board that i bought from menards. I cut them down into smaller sizes with a table saw. I then used a jigsaw to make the final shapes. Using some scotchbrite pads worked well to sand down the edges and make everything nice and smooth. I have 3 psu's on the lower board, and 1 psu & 4 power injection boards & the smart differential reciever board on the top board. I have a 1/2" air gap from the top of the lower psu's to the top board. Hopefully this is enough of an air gap. I did install a small fan mounted to the top air vent to help with air flow. To mount the psu's i used some M4x12mm screws. To mount the power inj boards and the controller board i used 3/4" long 6-32 screws with washers and lock nuts, i spaced these off the hdpe boards with some 6mm x 7mm od x 4.1mm id nylon spacers that i got on amazon. To mount the hdpe boards i used 2.5" long 10-24 screws with some white tubing and washers and lock nuts.

PSX 20220725 223335 copy 1501x2731
20220725 221712 copy 2731x2048

Reply
Posts: 37
Topic starter
(@tbm878)
Trusted Member
Joined: 9 years ago

These tools helped with the installation....

Wire strippers to take the outer jacket off the 18-3 cables

Screenshot 20220726 060656 Chrome copy 1102x2731

Klein wire strippers, worked really well to strip the wires

Screenshot 20220728 051248 Chrome copy 1102x2731

Fuse pullers for the tiny board fuses

Screenshot 20220728 051406 Chrome copy 1102x2731

I cut a slot in a 15mm deep well socket to tighten the pg7 cable glands from the outside of the box with the 18-3 wires in them. Worked really well with the tight spacing

20220730 212247 copy 1854x2731

Reply
Posts: 37
Topic starter
(@tbm878)
Trusted Member
Joined: 9 years ago

I did a power calculation to check which power injection method would work to give good voltage across all 800 pixels. I took Martin's past suggestion on power injecting everything and not relying on the controller power output. This is what i chose, power injecting at pixels 0 + 250 + 450 + 700. I use 1 controller channel output for these 800 pixels. 3 channels per 2400 pixel matrix. I will likely keep brightness to 20-30%, but i sized everything to be able to run at about 50% and be safe. 800 pixels x .72w per pixel x 50% rating = 288 watts used.

Screenshot 20220203 100151 Chrome
20220724 210357 copy 2731x2048

Reply
Share: