Notifications
Clear all

Need pin out

12 Posts
9 Users
0 Reactions
4,014 Views
Posts: 122
Topic starter
(@schuricg)
Estimable Member
Joined: 11 years ago
[#40863]

Just received a box full of pixel nodes from Ray Wu. My problem is I have no idea how the plugs are wired. Does and one know how they are wired looking at the plug with the key at the 12 o'clock position or know how they should ohm out?
100 node DC12 WS2811

Sent from my iPhone using Tapatalk


11 Replies
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

your pixels came prewired from Ray? with he waterproof connector


Reply
Posts: 105
(@pakeonoahu)
Estimable Member
Joined: 11 years ago

Top Left - GND
Top Right - 12V
Bottom - Data in


Reply
bcstuff
Posts: 449
(@bcstuff)
Reputable Member
Joined: 16 years ago
pakeonoahu wrote:Top Left - GND
Top Right - 12V
Bottom - Data in

It might be, but I wouldn't 100% count on that being the actual pin out.

You need to provide more information about the pixels, like a link to them on the website.


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

the wire that does NOT go all the way through is the data line. power and ground are more difficult. if you can identify the power or ground at a pixel, you can put a pin into the wire and measure from there


Reply
Posts: 944
(@didjareally)
Noble Member
Joined: 12 years ago

Email him and ask him how he wired them up, or check the item listing if they were listed as pre-wired, ray almost always puts a wiring diagram on there


Reply
JCook
Posts: 1003
(@jcook)
Noble Member
Joined: 13 years ago
bcstuff wrote:It might be, but I wouldn't 100% count on that being the actual pin out.

You need to provide more information about the pixels, like a link to them on the website.

I have some strings from Ray too, they came with the plugs on the ends. I also soldered hundreds of his pigtails for my show. I agree with the positions stated above but would add this

Top Left - GND - BLUE wire
Top Right - +DC - Brown Wire
Bottom - Data - Yellow.

You should be able to see these colors at the first node and see what terminal they are connected to.


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

If you have a multimeter with a diode tester you should be able to figure this out with a measurement of the Diode Forward Voltage.

See:
http://doityourselfchristmas.com/forums/showthread.php?40939-Tip-How-to-identify-5v-vs-G-on-pixels-with-same-color-wires

Between two of those pins you should see a voltage of 0.6. Those would be data & ground, and the other would be 12V. (Assuming these are WS2811 chips).


Reply
Posts: 122
Topic starter
(@schuricg)
Estimable Member
Joined: 11 years ago

Pin out and position was correct. My problem ended up just being a dead string. Looks like the data line is not passing through. Power and ground were good but not driving pixels. Replacement on its way. Great customer support from Ray!

Sent from my iPhone using Tapatalk


Reply
JCook
Posts: 1003
(@jcook)
Noble Member
Joined: 13 years ago

Did you hook this up to a controller? If the entire string is dead then the issue is in the plug. You may find that if the data line is a problem that it is just 1 bad pixel that is not passing the data down the line.


Reply
Page 1 / 2
Share: