sck1ng wrote:How big is this sign? Not sure if your using the DIYLEDExpress board or not..
It is. Bought it from Todd. It is 17x10 pixels.
With work, I haven't had a chance to repost here. I actually didn't have any issues with power. Put it together and in test mode works fine. I am running 13.8v out of a Radio Shack 25amp ham radio supply. So we will see with one of my PC supplies what it will do.
Wonder if with that setup the pixels were getting TOO MUCH power. The first 10 or so actually never quite go completely dark when in test mode. Just a fraction of "Pink" (tiny,tiny) is still there in between color changes. After those 10 or so, it is fine. So maybe the PC supply will do fine for it.
Ok,
So it was too much power (13.8v). Changed to another supply (12.3v) and that solved the pink issue.
Now I can't get this thing to work right with Nutcracker. I have tried several different node layouts in the models. Nothing will work correctly for the patterns in Nutcracker.
Here is my layout that I have. Looking at the back, the controller is in the bottom left corner. I ran the nodes up from the bottom left corner and then over to the next line top...and then it goes down that line. Over a line and back up. So really zig zag up then down.
Is that the wrong way of lining a matrix? Really hope I don't have to rewire since these came off of strings of 50. All 17 lines are soldered and heat shrinked. Hope it will work...but how?
I zig zagged from left to right then up and right to left.. I programmed my e6804 the zig zag pattern so now it sees it properly.. I have not tried to do any programming with it yet.. That's my plan by the end of the week. I will be using Vixen 3.1 for the programming though
Sent from my iPhone using Tapatalk
RobertB wrote:Ok,
Now I can't get this thing to work right with Nutcracker. I have tried several different node layouts in the models. Nothing will work correctly for the patterns in Nutcracker.Here is my layout that I have. Looking at the back, the controller is in the bottom left corner. I ran the nodes up from the bottom left corner and then over to the next line top...and then it goes down that line. Over a line and back up. So really zig zag up then down.
In Nutcracker, you want to setup a vertical matrix starting on the bottom left. If you have only 1 real string, then you can set Nutcracker to 1 string with 17 strands. If that doesn't work, post a pic of your Nutcracker model and we can maybe point out what is wrong.
CaptainMurdoch wrote:In Nutcracker, you want to setup a vertical matrix starting on the bottom left. If you have only 1 real string, then you can set Nutcracker to 1 string with 17 strands. If that doesn't work, post a pic of your Nutcracker model and we can maybe point out what is wrong.
THAT did the trick. If any other newbie to pixels...like me....are looking through the forum for answers... this is your fix (Thanks!!!). The stuff that it was doing was kind of like showing channels in the wrong place. In other words many of the pixels were not showing in the right place. It is now 🙂
Now if I can just fix this one pixel that will not go out. When everything else is off, it stays on green. All the colors in this one pixel is fine though.
Also, crummy text from Nutcracker. Guess that might be a font setting?
Does anyone have a xLights "Text" sequence they would be willing to share? I am really not liking what I am seeing on the text test patterns I am trying.
As mentioned before, my matrix is just a basic 10x17 pixel matrix. It is just not very legible.
Try courier font with smallest font size
Go through the fonts, look for fonts that have the smallest font size. Your matrix is not optimum in width. Build models 10x17, 10x34, 16x50. Then try text on it. You can use these models to see what text would look like on diff size hardware.
smeighan wrote:Go through the fonts, look for fonts that have the smallest font size. Your matrix is not optimum in width. Build models 10x17, 10x34, 16x50. Then try text on it. You can use these models to see what text would look like on diff size hardware.
Well that's not good. I tried different settings than the one suggested 1 string 170 nodes per string, and 17 strands. Anything else but that, the text jumps all over the place. Almost afraid with the text being so large...and having to scroll (don't want to go to fast)...people will miss it. So hardly any time for animation 🙁
Looks like I will have to use the regular Holidaycoro mini light sign again....sigh 🙁
Text shouldn't jump. If you pick text and scroll left it should be smooth, the issue is you Carly see a few letters because your horizontal width is 17 pixels. If u can take a movie of your screen so I can see what this jumping is

