Lights acting up
 
Notifications
Clear all

Lights acting up

10 Posts
4 Users
0 Reactions
2,955 Views
Posts: 5
Topic starter
(@rampc)
Active Member
Joined: 10 years ago
[#43239]

Hello all,

I'm new around here and kind of new to this form of lighting, just over a year. I was wondering if any of you would be willing to watch this video and let me know if you might know what is going on with the lights on the left hand column(96 pixels), it is also happening on another string of 19 pixels. The set up is 1 SanDevice E682 with around 460 RGB pixels and a 30amp power supply and running Vixen 3. Thank you for any help you can offer.


9 Replies
MindTrik
Posts: 1542
(@mindtrik)
Noble Member
Joined: 16 years ago

It's hard to say without knowing how things are set up....distance to first pixel...etc. either a bad data connection or power. Can you swap a data line and see if the issue stays with the pixels?

Sent from my SM-G930T using Tapatalk


Reply
Posts: 825
 DanJ
(@danj)
Prominent Member
Joined: 13 years ago

Total guesses..... Maybe you have a power issue (low voltage) or signal issue e.g., a signal lead that is too long or a bad connection (E682 will only push something like 30' max signal length from the controller to the first pixel...). Suggestions--run some tests from your E682 or from your sequencing software through your E682 to help you pinpoint what is going on.


Reply
Posts: 5
Topic starter
(@rampc)
Active Member
Joined: 10 years ago

Distance to the first pixel is only about 6 feet. I install data cabling for a living and have tested the data connection.


Reply
Posts: 5
Topic starter
(@rampc)
Active Member
Joined: 10 years ago
DanJ wrote:Total guesses..... Maybe you have a power issue (low voltage) or signal issue e.g., a signal lead that is too long or a bad connection (E682 will only push something like 30' max signal length from the controller to the first pixel...). Suggestions--run some tests from your E682 or from your sequencing software through your E682 to help you pinpoint what is going on.

I'll try changing outputs and see if it follows.


Reply
MindTrik
Posts: 1542
(@mindtrik)
Noble Member
Joined: 16 years ago

Yeah Yeah yeah...you install data cables...but you're asking for help and each of us have our own process of chasing issues. Could be a bad pigtail as well...

Sent from my SM-G930T using Tapatalk


Reply
Posts: 5
Topic starter
(@rampc)
Active Member
Joined: 10 years ago
MindTrik wrote:Yeah Yeah yeah...you install data cables...but you're asking for help and each of us have our own process of chasing issues. Could be a bad pigtail as well...

Sent from my SM-G930T using Tapatalk

Sorry, I didn't mean to sound dismissive or ungrateful I was just trying to say that I had ruled that out. Thank you for your suggestion, It was a very valid point of failure.
I will check the connections, I'm not using pigtails, 18/3 directly to the screw terminals and soldered at the string covered with double wall shrink tube.


Reply
MindTrik
Posts: 1542
(@mindtrik)
Noble Member
Joined: 16 years ago

LOL..I was just poking fun. We all can overlook stuff. The first thing I would do is try to see if it moves with different ports. That way you can at least condense the issue down . Is it the whole string or a part of it?

Sent from my SM-G930T using Tapatalk


Reply
Posts: 5
Topic starter
(@rampc)
Active Member
Joined: 10 years ago
MindTrik wrote:LOL..I was just poking fun. We all can overlook stuff. The first thing I would do is try to see if it moves with different ports. That way you can at least condense the issue down . Is it the whole string or a part of it?

Sent from my SM-G930T using Tapatalk

It is only happening on the last 30 or so of a 96 pixel string.


Reply
Posts: 241
(@mrdudeman)
Reputable Member
Joined: 12 years ago

try some voodoo.
move the problem wire around in relation to all the other wires. I find this often gets rid of that sort of problem.
ie... distance the wire from the others. or maybe even get the wire closer to the others. if you have 3 individual wires to the strip, separate the data wire away from the other wires


Reply
Share: