How to implement 10...
 
Notifications
Clear all

How to implement 100 null pixels?

68 Posts
11 Users
0 Reactions
10.7 K Views
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago

1pet2_9 - where do you stand? This discussion has meandered all over the place, so I don't know which direction you might want to take. I'm willing to help, and I'm sure that others are as well.


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago

Hi Phil (P. Short), my design dates back to 2017 and was built from parts I had on my bench to if I’m honest prove a point to someone who said that the ATMega328 wasn’t fast enough to be used the basis of a pixel splitter. Whilst it works well and can be easily DIYed from common components we are now 5 years on and live in a world where you can have PCB’s assembled from components most of us don’t have eyesight to see and at a price for an assembled board that is less than these days the shipping cost of components to DIY yourself.

I think there will always be a practical reason for maximising channels on an output whether it be the cost of the controller you have purchased, the number of Wi-Fi based controllers you have and the other network traffic in your area.

The most interesting part of the conversations has been how do you set the number of channels to mask for something that is small and weatherproof. A couple of the most viable that I’ve seen where:

Repeatedly send a specific set of channel data for 15 minutes which is recognised as programming data as opposed to show data.
Using a reed relay to put the device into programming mode and then sending data to specify the values.

I’m interested to see where your project goes as the ‘Pixel Splitter’ has generated more interest than I ever imagined.

Stay safe.
Phil.


Reply
Posts: 105
(@pakeonoahu)
Estimable Member
Joined: 11 years ago

I have been interested in the splitter for a while but not for splitting, I want to use it as an absorber, it always rain in my area from Nov to Dec, especially this year has been very heavy and daily, no matter how much waterproof I did for the connectors, water always got into them, and no matter how much I tested the pixel, after sun/heat and rain, few pixels will act up until they are dried or replaced. I also have some long runs and power injected, once a pixel not passing data, whatever behind it will die or blink randomly. I want something that can by pass the bad segment, if I can take out one string of X amount of pixels and replaced with the splitter/absorber that has the same count, I would be happy to do that in dark/rain like 5 minutes, so my other pixels don't look stupid compare to the rest of the props, then I can test and repair the bad strings. This way I don't have to mess with FPP configuration and/or controller settings.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago
Barnabybear wrote:Hi Phil (P. Short), my design dates back to 2017 and was built from parts I had on my bench to if I’m honest prove a point to someone who said that the ATMega328 wasn’t fast enough to be used the basis of a pixel splitter. Whilst it works well and can be easily DIYed from common components we are now 5 years on and live in a world where you can have PCB’s assembled from components most of us don’t have eyesight to see and at a price for an assembled board that is less than these days the shipping cost of components to DIY yourself.

What about steadiness of hands...

I think there will always be a practical reason for maximising channels on an output whether it be the cost of the controller you have purchased, the number of Wi-Fi based controllers you have and the other network traffic in your area.

The most interesting part of the conversations has been how do you set the number of channels to mask for something that is small and weatherproof. A couple of the most viable that I’ve seen where:

Repeatedly send a specific set of channel data for 15 minutes which is recognised as programming data as opposed to show data.
Using a reed relay to put the device into programming mode and then sending data to specify the values.

If I was to use a reed switch I would probably just use successive closures of the relay to rotate through a small sequence of channel counts, such as 50,100,150,200 pixels, with changing output colors to indicate which setting is active, and then write the count to non-volatile memory when a certain amount of time has elapsed without any switch closures. The reason for this is that it might not be convenient to send that pixel data when the module is out in the field (unless you were thinking of setting the bypass count when the module is on a workbench).

I’m interested to see where your project goes as the ‘Pixel Splitter’ has generated more interest than I ever imagined.

I'm not sure how much interest there is besides 1pet (if they are even interested).

Stay safe.
Phil.

Thanks,


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago
pakeonoahu wrote:I have been interested in the splitter for a while but not for splitting, I want to use it as an absorber, it always rain in my area from Nov to Dec, especially this year has been very heavy and daily, no matter how much waterproof I did for the connectors, water always got into them, and no matter how much I tested the pixel, after sun/heat and rain, few pixels will act up until they are dried or replaced. I also have some long runs and power injected, once a pixel not passing data, whatever behind it will die or blink randomly. I want something that can by pass the bad segment, if I can take out one string of X amount of pixels and replaced with the splitter/absorber that has the same count, I would be happy to do that in dark/rain like 5 minutes, so my other pixels don't look stupid compare to the rest of the props, then I can test and repair the bad strings. This way I don't have to mess with FPP configuration and/or controller settings.

Aren't there pixel strings out there that have two parallel data paths so that if one goes bad, the other signals can still go down the second path? Or am I just imagining that these exist, that they aren't outside of your budget?

Also, at the moment I don't see how these pixel splitters would help. Could you walk me through a scenario?


Reply
Page 8 / 14
Share: