Help - Troubleshoot...
 
Notifications
Clear all

Help - Troubleshooting Mega Tree

11 Posts
4 Users
0 Reactions
1,628 Views
Posts: 13
Topic starter
(@justaplaneguy)
Eminent Member
Joined: 5 years ago
[#58389]

I have a 16 Line 180 degree mega tree.
Each Line contains 147 pixels / bulbs

As such I have 4 PixelPop controllers
Each controller operates 4 lines
1 String in xLights = 4 physical lines.
Every physical line has power injection.

As an example. Starting from the Top Left of the mega tree is where the connection is made to Controller #1. The line goes from the top the ground (147 bulbs), then has a connector the next line and goes all the way to the top (another 147 bulbs), then it connects at the top to a third line goes to ground (another 147 bulbs), connects at the bottom to the 4th line and goes to the top (another 147 bulbs). So in Xlights, all of this (588 bulbs / nodes) is 1 String.

Then it Starts all over again Starting again at the top but this time to Controller #2, and so on and so forth until we're done and have 4 Strings in X-Lights.

Every String has +V and -V to it. Doing a Rainbow Test, Chase Test, etc. Seems to work correctly.

When I render a show in Xlights however, and then hit the light bulb to run the show, the colors are completely jacked and messed up. Like I've got blues and purples, when they should be red and green, and things just aren't rendering properly at all.

Is this a data issue? Wireless network too weak (RSSI at -65ish)?


10 Replies
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
justaplaneguy wrote:
Like I've got blues and purples, when they should be red and green

It sounds like you have blue and green swapped in the controller. I don't use PixelPop controllers but every controller seems to have they're own internal configuration program. There is where you set the order of the colors. No idea why, but the seems to undefined color order in pixels, so you have to tell your controller what you have.


Reply
Posts: 13
Topic starter
(@justaplaneguy)
Eminent Member
Joined: 5 years ago
ErnieHorning wrote:
It sounds like you have blue and green swapped in the controller. I don't use PixelPop controllers but every controller seems to have they're own internal configuration program. There is where you set the order of the colors. No idea why, but the seems to undefined color order in pixels, so you have to tell your controller what you have.

Thanks but then why would the testing work just fine? I can pick any color in a chase, or a static, and it's displayed correctly.


Reply
Posts: 13
Topic starter
(@justaplaneguy)
Eminent Member
Joined: 5 years ago

Ok, So there does seem to be a problem in my setup. I want Controller 1 to operate String 1 as one really long string. When I do an RGB Cycle test, A-B-C, it's splitting it up by every 170 bulbs, Instead of showing all 588 as RED, Then Green, then blue.

Not sure what the deal is.


Reply
Posts: 13
Topic starter
(@justaplaneguy)
Eminent Member
Joined: 5 years ago

It has everything to do with the layout and the controllers. I can't seem to setup the Mega Tree correctly in xLights. It either wants to show the lights correctly for just the first 170 bulbs (510 channels) and not address the others. Or It addresses all the strings but incorrectly and gets all jacked up on the colors.


Reply
Posts: 13
Topic starter
(@justaplaneguy)
Eminent Member
Joined: 5 years ago

I drew out the tree and how it's connected. I could really use help here because no matter what I've tried for the controller or the layout, I can't seem to get this to work. The only time it gets the right colors, is if I set the controller to "Auto Size", however, then the tree only lights up the first 170 pixels for each controller.

IMG 7472

Reply
Posts: 89
(@rreese)
Estimable Member
Joined: 5 years ago

What pixelprop controllers do you have that only have a single output?
Normally a mega tree is built with the connections at the bottom of the tree.
While its a busy time and you might have to wait a bit, the xLights zoom room should be able to help.

https://zoom.us/j/175801909?pwd=ZU1hNzM5bjJpOGZ1d1BOb1BzMUFndz09


Reply
Posts: 13
Topic starter
(@justaplaneguy)
Eminent Member
Joined: 5 years ago

Not a pixelprop controller. A "PixelPop" controller. These are DIY built ESP8266 wifi controllers that are programmed with the Epixelstick v3.0 software (you can actually buy circuit boards that you solder the components to on this forum). When you construct the controller and the connections to it, you end up with a Voltage Input, a 3 Wire RGB output, and an extra 2 Wire Voltage output for power injection.

Article here --> https://www.instructables.com/WiFi-Controlled-Christmas-Lights-With-ESP8266/-

Shows what the controller board and finished controller looks like right at the top).

I have run this setup once before (about 3 years ago) but re-built my strands this year because I was using 3" spacing the last time, and this time I used 1" spacing (more lights, etc.). It worked flawlessly. That said, since it's been some time since I've picked xLights back up again, I'm having some issues getting xLights to talk to the lights correctly (or rather, address the larger strings).


Reply
Posts: 85
(@memphislights2)
Trusted Member
Joined: 2 years ago

post your xlights config for the controller and the definition for your tree

Also, do you have to upload your configuration or manually setup channels on the pixelpop?


Reply
Posts: 13
Topic starter
(@justaplaneguy)
Eminent Member
Joined: 5 years ago
memphislights2 wrote:
post your xlights config for the controller and the definition for your tree

Also, do you have to upload your configuration or manually setup channels on the pixelpop?

Actually, just as I was testing, I at "least" got the lights addressing and performing the right colors as they are supossed to. That problem was resolved by logging into each controller's web page separately, changing the universe boundaries to coincide with the controller setup in xlights to 510, and the start universe to the same universe as setup in xlights controller setup.

This at least resolved this problem. I never had to do this before, whatever I put in Xlights as the controller setup automatically flowed over to the controller itself.

Now, however, I seem to have an issue specfically with Controller #2, as it's lagging and getting a bunch of sequence errors. I think it's either the board or the programming of the board. I'm looking into it....


Reply
Page 1 / 2
Share: