WS2811 Strip Props ...
 
Notifications
Clear all

WS2811 Strip Props Flicker

5 Posts
4 Users
0 Reactions
941 Views
Posts: 10
Topic starter
(@navyswo91)
Active Member
Joined: 5 years ago
[#58386]

I have built five different sticks/poles to place inside some Christmas light bulb props. Each stick is comprised of 18 WS2811 strip pixels I cut from a 5M roll. I soldered on JST connectors to each 18 pixel strip. Then I soldered a JST connector to an xConnect pigtail to connect the first stick to a port on a Falcon SRx1 board (Kulp 16A-B is main controller). The remaining 4, I chained together using the JST connectors. I model them in xLights and everything works great (1st pic).

So now I want to put the sticks into the props that will be a few feet from each other and I want to improve upon the connections. So I soldered JST connectors to more xConnect pigtails with the plan of chaining the props together using the xConnects. However, once I place the first xConnect pigtails between props 1 and 2 I get intermittent flickering of the outboard four sticks. Sticks 2-5 are still connected via JST, with only stick 1 and 2 using the xConnect pigtails. First thought was that the solder sleeve joints between the JST (22AWG?) connector and the 18AWG pigtails are suspect, although a multimeter continuity check works on each pigtail just fine. So I decided to test by skipping soldering and just Wago-ing (?) the JST connector to the pigtail but it results in the same flickering. I thought perhaps the extra ~3ft is a problem, so I created a 4ft 22AWG wire with JST on each end (eliminating the pigtails) and placed it between prop 1 and 2. Flickering goes away. So I stumped.

Is the use of 18AWG connected to the higher gauge wire on each pixel strip causing data problems? It can't be the ~3ft of length affecting data can it? What am I missing?

Any feedback from the experts here would be much appreciated.

Sticks Connected JST
Sticks with xConnect

4 Replies
Posts: 27
(@k-mob)
Eminent Member
Joined: 6 years ago

I'm interested if you've figured anything out. I'm finding these strips to be rather finicky as well. Just weird that despite power injection, I'm finding sometimes that a length of wire will wreak havoc, and in other places, a longer length of wire (with no power injection) between sections is fine. Scratching my head...


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

I found that it had more to do with a good ground wire, since that's what the data line is referenced to. And I'm almost exclusively using the ESP8266 that a lot of people shun because it's only a 3 volt output. Every one of these props is controlled by a single ESP8266 D1 mini and no level shifter or resistor. All of these are also seed (pebble) and the shunned 5 volt variety too!

All power to the D1's is soldered directly to Vin and Gnd and passed through waterproof automotive connectors. The USB connector is only used for initial programming of WLED and any changes are are afterwards done through WIFI. Sequencing is through xLights. Maybe beginner's luck, but there is no flickering on any of these.

The sun was my first prop. I did tie all the power and grounds together, just because everyone said I had to. It's bullet pixels run by an ESP8266 at 5 volts though. The Minions are controlled by a Pocket Pixel controller (that I won at the Minnesota Mini) running WLED at 12 volts. This is an ESP32 and probably does have built-in level shifters.


Reply
Posts: 27
(@k-mob)
Eminent Member
Joined: 6 years ago

Thanks for sharing. Do you have a write up for this somewhere, or a go-to resource that would help someone get started? I think moving to local control and wifi could be the next step of my pixel evolution rather than figuring out new ways to stretch out the four ports of my Falcon.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago
ErnieHorning wrote:
Maybe beginner's luck,

Or maybe good soldering skills and the sense to keep things simple.


Reply
Share: