Thank you for the close-ups. I don't have that much room behind my fascia. The good news is that the soffit is all new construction from an addition I put on the house last summer. ...and it isn't sided yet. When it gets a little warmer I'll come up with a plan then. But now that I see your layout I have a better feel for the work ahead.
I have 30 pieces built now and have had some time to test how I'll power them... and I see the voltage drop after a set of 3. When I power them from both ends I can get 2 sets as you suggested. I'll need around 75 of them, but I only have enough parts on hand to make 60 so I'm putting an order together for the rest tonight. Keeping my fingers crossed the color matches when the newer strips come.
Today while waiting for electrical inspections for the new addition, I made a 40' long 16 gauge harness for the 12 volt power. Placing the power supply in the middle I can tap in converters all along it. Going to have to be creative to hide all this... Dawn was looking at them with a simple RGB twinkle and told me to go hang them on the house now. Sure made me feel good about the whole thing...
Jeff
Question:
Are the Plasma Icicles PreSale on DIYLEDExpress.com expected to be similar to the ones you made? What are the primary differences I should know about?
I really am interested in purchasing these units but I want to double-check before I submit a big order.
The one difference that stands out is Todd's production model will have a connector at the beginning and end of a set of 3 Icicles(30 Pixels)
EDIT: This next statement was misleading in my first write of this post. The failed pixels in the next statement have nothing to do with Todd's pixels. I purchased 4 rolls of WS2812B pixels from Ray Wu late last summer. (My apologies Todd... 🙂 )
So far, I've found 2 bad pixels out of 600. I haven't had them powered for more than a few minutes so I have no idea how reliable they are. I like the fact that I can remove a single Icicle if something fails. Understand that a failed pixel will trash everything downstream of it so it has to be replaced immediately.
I needed to order 4 more ribbons and 100 more connector sets to complete the prop. All told I'll have around $400 invested for 45', to include a 12V PS, 14 DC to DC converters 12mm silicone tube, 6 WS2812B ribbons and somewhere around 100 connector sets. Shipping and the 16 gauge zip cord for 12V aren't included in the price.
Jeff
Jholmes wrote:Question:Are the Plasma Icicles PreSale on DIYLEDExpress.com expected to be similar to the ones you made? What are the primary differences I should know about?
I really am interested in purchasing these units but I want to double-check before I submit a big order.
There are a few main differences. First, the icicles offered in my store do not have connectors between each icicle. They are sold in sections of 3 icicles.
Second, the icicles in my store have the silicone tube and are also filled with silicone for added waterproofing.
Third, my icicles come with 18" of wire between each icicle.
edited
tjetzer wrote:For those not following this thread, Jeff is building his own icicles. The bad pixels are his own and not from icicles or strips purchased from DIY LED Express.
Sorry for the run-on paragraph Todd. I edited it to correct.
Jeff
Jeff Millard wrote:Sorry for the run-on paragraph Todd. I edited it to correct.Jeff
No problem Jeff. I just didn't want any confusion. Thanks!
Some people have asked me my opinion of Todd's Plasma Icicles. I still have not seen them but I do have a couple of comments regarding his explanation of the differences from my originals.
1. He did not use connectors for every icicle. To me that means a few things. Lower cost to the end user. A bit less voltage drop due to connectors, and I would guess somewhat easier to install in most applications. That would not have worked for my particular installation at every sections because when I went around corners I needed to add jumpers between icicles. If it happens at the end of the cluster no problem, but mine didn't work out that way. Seems like a cost vs convenience thing. I would think Todd chose correctly for most of us since cost seems paramount to many and most can add a connector if needed. As well, replacing one single icicle should there be a failure, is easier than replacing 3 icicles. [Just a note: Once I was up and running I had only one pixel fail in my entire system and it was very early on before I officially started the nightly run. After that, flawless the entire month].
2. Todd is filling his Plasma Icicles with silicon to make them more water proof. This surprises me since he has held the cost down very well and still incorporated this added feature. Way to go Todd! I personally didn't fill mine because I didn't see the need, (I actually have the equipment to do that).... But then again I am not selling them to others who will use them God knows where. Mine were to stay right here at home in California! :thup2:
3. He is using 3 pin connectors and not the 4 pin I chose. My choosing the 4 pin system was strictly how I chose to run my data and power injection. I am assuming he has a scheme for injecting power and continuing data runs thru several strings, I haven't seen it yet but I hope to soon.
My 2 cents worth,
Craig
Love these picicles, gotta have some, gotta. From putting things into and out of my cart on Todd's site, it looks like the plan is to use a 3 conductor T for the power injection. Which I am thinking you would have to run another set of wires and connectors to get into the T with, so perhaps your 4 conductor might be better long term because you can run power on two lines and maybe not need power injection?
So have you tried power on two of the wires and did it get you much further runs? Perhaps with the 4 and being able to inject power on both ends using two wires?
arw01 wrote:Love these picicles, gotta have some, gotta. From putting things into and out of my cart on Todd's site, it looks like the plan is to use a 3 conductor T for the power injection. Which I am thinking you would have to run another set of wires and connectors to get into the T with, so perhaps your 4 conductor might be better long term because you can run power on two lines and maybe not need power injection?So have you tried power on two of the wires and did it get you much further runs? Perhaps with the 4 and being able to inject power on both ends using two wires?
Actually the reason I used 4 pin and not 3 pin had nothing to do with the wire size. Running 2 wires on the positive and only one wire on the common will not really gain you that much. I inject power between every 6 Plasma Icicles. I use the same data line and common but inject positive to every other set of 6 Icicles on a different wire. You can see why on the PDF in my dropbox. I haven't really thought about doing it with 3 conducts but I imagine you could.
