Finally got em fini...
 
Notifications
Clear all

Finally got em finished.

162 Posts
38 Users
0 Reactions
54.4 K Views
hasoon
Posts: 520
(@hasoon)
Honorable Member
Joined: 15 years ago
dsmjuggalo wrote:Todd has his version of these listed in his presale right now. I will be buying them for sure.

Link?


Reply
dsmjuggalo
Posts: 663
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

http://www.diyledexpress.com/index.php?main_page=product_info&cPath=42_53&products_id=249


Reply
hasoon
Posts: 520
(@hasoon)
Honorable Member
Joined: 15 years ago

Thanks! I don't know how I missed them.


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 20 years ago

I love these! I started making them from parts I already had. Thank you Pythan for sharing such a great idea. I just went out in the shed and bagged up the old icicles for Goodwill.

I used 12mm tube, so I was able to slide it up over the waterproof connectors. I wanted them to be a little closer together so I cut the wire down a little. I'm going to test and try 12 to 5 volt DC to DC inverters and see if I can get away with using stuff I already have in hand. I don't have near as far to travel, just 45' total. If it doesn't work I'll just run a larger gauge wire parallel to the strings. Really looking forward to getting these finished.

Jeff

Pixicicles

Reply
Posts: 2229
Topic starter
(@plasmadrive)
Famed Member
Joined: 15 years ago
Jeff Millard wrote:I love these! I started making them from parts I already had. Thank you Pythan for sharing such a great idea. I just went out in the shed and bagged up the old icicles for Goodwill.

I used 12mm tube, so I was able to slide it up over the waterproof connectors. I wanted them to be a little closer together so I cut the wire down a little. I'm going to test and try 12 to 5 volt DC to DC inverters and see if I can get away with using stuff I already have in hand. I don't have near as far to travel, just 45' total. If it doesn't work I'll just run a larger gauge wire parallel to the strings. Really looking forward to getting these finished.

Jeff

Hi Jeff,

You are welcome.. if you have any questions.. just ask.

You will find the DC-DC converters work great as long as you use big enough ones. For my Plasma Icicles I wound up using 3.3amps for 2m worth of pixels (6 icicles) at 5vdc with all on white.. And of course I center fed them between every six icicles. And the white is very white if you have stable 5v power at the pixels. That is the one place not to cheap out.. "we got to have more power captain"! LOL

Hope everyone that want's the Plasma Icicles gets them, whether purchased or home made DIY style.. Ironically, I may never get to use mine again if I shutter my show..


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 20 years ago

I've got 12 to 5 volt 3 amp converters. When I get a few sets of them made I'll test to see how that works. I just fired the first set up. Magical! It's great when it's this much fun. Bonus, my wife saw your solder station in a photo. She said I have to have one of those. Gosh I love her.

Jeff


Reply
Posts: 2229
Topic starter
(@plasmadrive)
Famed Member
Joined: 15 years ago
Jeff Millard wrote:I've got 12 to 5 volt 3 amp converters. When I get a few sets of them made I'll test to see how that works. I just fired the first set up. Magical! It's great when it's this much fun. Bonus, my wife saw your solder station in a photo. She said I have to have one of those. Gosh I love her.

Jeff

That is how I felt!
Glad you get a bonus to boot :rolleyes:


Reply
Posts: 238
(@ronp5683)
Reputable Member
Joined: 14 years ago

Love these lights.

But, yes there is always a but. Your eves have a very steep pitch, and mine is mostly flat. So 20 inch iclces are not the best length. Something half that length would be best for most people, like the commercially available lights. So when diyledexpress offers these I am in, otherwise I stuck making my own.


Reply
Jeff Millard
Posts: 1450
(@jeff-millard)
Noble Member
Joined: 20 years ago

A couple things: If you build these, be very careful to make sure you have the orientation of the male and female connectors in the correct direction. No matter how hard I tried, I kept getting them reversed. Test the ribbon before you build. I did and found 2 bad pixels before even starting.

After making the first set of 3, I changed to production mode. Things are going much faster this way. I had 35 sets of connectors on hand and was able to get them all prepped to be soldered to the ribbon in an afternoon. I'm also using a hot glue gun to attach the long data wire to the back of the ribbon. As I said earlier I used 12mm tube and that wire can work it's way to the side and become visible. With the larger tube I'm able to slide it over the wire from the waterproof connectors. I haven't sealed anything yet because I want to get them all built first. I'll add Silicone, slide the cover over the wire and wire tie the cover. I have the same style end cap Pythan used.

I don't have a plan yet to house the DC/DC converters but they're small and waterproof so it shouldn't be a big problem.

This WS2812B ribbon is some nice stuff. Brighter than the TLS3001 ribbon I used on my North Poles. The color looks bolder too.

Pythan, what did you use to hang them? I have some old gutter clips, but using them would mean these would have to hang in front of the gutter. I'd like them to hang under the gutter from the fascia. I want a clear separation from the roof outline I'm making with coroplast over ribbon.

Jeff


Reply
Posts: 2229
Topic starter
(@plasmadrive)
Famed Member
Joined: 15 years ago
Jeff Millard wrote:A couple things: If you build these, be very careful to make sure you have the orientation of the male and female connectors in the correct direction. No matter how hard I tried, I kept getting them reversed. Test the ribbon before you build. I did and found 2 bad pixels before even starting.

After making the first set of 3, I changed to production mode. Things are going much faster this way. I had 35 sets of connectors on hand and was able to get them all prepped to be soldered to the ribbon in an afternoon. I'm also using a hot glue gun to attach the long data wire to the back of the ribbon. As I said earlier I used 12mm tube and that wire can work it's way to the side and become visible. With the larger tube I'm able to slide it over the wire from the waterproof connectors. I haven't sealed anything yet because I want to get them all built first. I'll add Silicone, slide the cover over the wire and wire tie the cover. I have the same style end cap Pythan used.

I don't have a plan yet to house the DC/DC converters but they're small and waterproof so it shouldn't be a big problem.

This WS2812B ribbon is some nice stuff. Brighter than the TLS3001 ribbon I used on my North Poles. The color looks bolder too.

Pythan, what did you use to hang them? I have some old gutter clips, but using them would mean these would have to hang in front of the gutter. I'd like them to hang under the gutter from the fascia. I want a clear separation from the roof outline I'm making with coroplast over ribbon.

Jeff

Hi Jeff,

You are running into some of the things I did.

I hung them on conduit with wire ties behind the fascia boards. I added some pictures at the end so you can see what I had hidden behind the fascia

Dropbox Logo Dropbox File (Private or Invalid)


Reply
Page 4 / 17
Share: