Notifications
Clear all

Pixel issues

12 Posts
4 Users
0 Reactions
3,807 Views
dsmjuggalo
Posts: 663
Topic starter
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago
[#27368]

I have had a issue arise. A little info about what I'm using. These are technicolor pixels spaced 8 inches apart with signal from a 682 and power from a computer power supply. Signal and voltage is sent through 18 gauge wire.

Problem 1
My garage is lined with 60 pixels and is about 15 feet from the controller. When I turn on full white it goes crazy, with random pixels doing whatever they want. Is this a voltage issue or do I need a null pixel in here.

Problem 2
My double window is lined with 44 pixels and is about 8 feet from the controller. As soon as I power up the controller I get random pixels firing at like 20% intensity. Not sure what's causing this at all.


11 Replies
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

Check your voltages near the beginning and end of the string. As what voltage pixels?


Reply
dsmjuggalo
Posts: 663
Topic starter
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

I'll check tonight. They are 12v


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

Internally the Technicolor pixels are a 5 volt pixel with a built in 78L05 regulator. How do I know? I have some of the bare boards plus Ray and I have been discussing these for quite awhile.

The 78L05 has a dropout of between 1.5 and 1.7 volts so that would be 6.5 to 6.7 off the cable. That allow up to a 5.3 volt drop from a nominal 12 volt at the input connector. I've measured my 50 pixel sample string, standard 7.75" spacing and 2 meter lead in, and they drop about 2.7 volts at full white. A 100 pixel string would be a little less than double that, since it does not have a 2 meter leader in the middle, so figure about a 5.3 volt drop. Not a problem with the 50 pixel string but I'd push the 12 volts to about 12.5 with a 100 pixel string.

BTW, even if the voltage gets below the dropout point the pixel should still function since the regulator should just look full on and with the output about 1 diode drop below the input. So you should make it all the way down to about 5.7 to 5.8 volts before the pixels even start to look pink.

I suspect you're having a problem with the input signal. Could be noise or a bad connection. If you have any WS2811 12 volt pixel laying around you could try it.

I've got about 800 technicolor pixels in custom lengths coming in the next couple of weeks. Most of them are 50 pixel strings with some 84, 64 and 32 pixels toss in. Spacing is 150 mm or close to 6" with short leaders rather than the long 2 meter ones.


Reply
dsmjuggalo
Posts: 663
Topic starter
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

I have 4 frames built with the technicolor pixels. A window with 32 that's 6 feet away, a door with 43 that's 3 feet away, a double window with 44 that's roughly 12-15 feet away and my garage door with 60 that's 18-20 feet away. The only issues I'm having are with the 2 that are furthest away. My roofline is 2811 12v pixabulbs one side has 39 that's 15 feet away and the other side has 71 that's 10 feet away and I have no issues out of those.


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

You might look at changing the series resistor values on the E682 to see if that helps. You can get away with 1/4w resistors while you're testing. There is a thread about this someplace.

I have some longer runs which is why I'm making some RS485 pixel extenders and use the pseudo RS485 mode on the E682. Hopefully I won't have to worry about flashing pixels.


Reply
dsmjuggalo
Posts: 663
Topic starter
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

I tested the garage and found out I had 5.9 volts at the end with full white. I injected some power to the very end and it definitely helped but I still have a slight flicker throughout the whole frame.


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

Unless you have a defective string I still think your problem is on the input end. Each pixel regenerates the data stream so the data should be clean between pixels. If you're getting glitches on the input it will follow down the entire string. As Jim says try different values for the series resistor in the E682.

BTW, here is the board used in Technicolor Pixels.


Reply
dsmjuggalo
Posts: 663
Topic starter
(@dsmjuggalo)
Prominent Member
Joined: 15 years ago

I'm gonna stop at radioshack when I get out today and pick up some resistors, any suggestions on which would be best to try, I have some 220 here but I don't know if that's far enough below the originals to make a difference


Reply
Posts: 419
(@txag2008)
Honorable Member
Joined: 17 years ago
I've got about 800 technicolor pixels in custom lengths coming in the next couple of weeks. Most of them are 50 pixel strings with some 84, 64 and 32 pixels toss in

Do you plan on using power injection with your 84 pixel strings?


Reply
Page 1 / 2
Share: