Falcon serial outpu...
 
Notifications
Clear all

Falcon serial output

28 Posts
8 Users
0 Reactions
16.4 K Views
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago
justinmiller24 wrote:Hi Kev,

I am planning on running both pixel and AC lights this year and have a Falcon F16v3 and Renard SS24 similar to what you describe here. Aside from getting the setting updated (baud rate etc) is there a specific patch cable I need to use to go from the F16v3 serial port to the SS24? If so would you mind pointing me in the right direction?

I am prepare to make one if needed, but if there is an adapter or something off the shelf for this I would prefer to go that route instead. Please let me know.

Thanks so much!

Justin

Thats the cable I made for the Falcon to the Renard.

Sent from my SM-G965U using Tapatalk


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

Try this picture.

Sent from my SM-G965U using Tapatalk


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

That is the one! Thanks guys.


Reply
Posts: 9
(@justinmiller24)
Active Member
Joined: 6 years ago
TomL8345 wrote:Justin,

Whether you need a specific patch cable for your setup depends on which firmware you have on your SS24. If you are running DMX firmware, you should be good to go, however, if you have Renard Firmware you will need to change the wiring either in a cable or adapter. There is a discussion on this topic currently going on at the Green Site. Post #6 in this thread shows you how to properly pin out the cabling.

It is much better to just make a short adapter with a male & female connection to keep with the controller. This allows you to use a standard ethernet cable rather than keeping track of a specific cable year to year.

Tom,

Thank you so much! I am not sure about the firmware since the SS24 was purchased from another user on DIYC, however I agree with having a short adapter with male/female connection to keep with the controller.

Thank you so much for the advice, the link, and for confirming. I will check out the Green Site. Again, really appreciate you following up!

Regards,
Justin


Reply
Posts: 190
(@harpster)
Reputable Member
Joined: 17 years ago

Sorry to say that the F16V3 will not work for Renard SSx standard Firmware. No cabling I have tried will work. There are other posts about this but the proven solutions are using the DYILEDEXPRESS Bridge or run a separate USB to RS485 cable.

I have 10 or so Renard SSx boxes. I run Ethernet cable from show computer to F16V3 and Eithrnet cable out of F16V3 to DYILEDEXPRESS Bridge. Then one of the 6 Bridge Ports to 1st Renard Box. I’ve used this setup for 3 seasons with no problems but you do need to get your Renard channels set up properly in your Sequencer.

Good luck!


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

Interestng. I run that exact cable with standard firmware straight from a Falcon F16v3 to the SS24 with no issues.


Reply
TomL8345
Posts: 1356
(@toml8345)
Noble Member
Joined: 15 years ago
Kev7274 wrote:Interestng. I run that exact cable with standard firmware straight from a Falcon F16v3 to the SS24 with no issues.

I did the same a couple of years ago from a F4V3...


Reply
Posts: 190
(@harpster)
Reputable Member
Joined: 17 years ago

Glad it worked for some people but I spent a lot of time on it and and definitely didn't work for me. I really like the F16V3 and it's my Pixel Controller of choice but not for Reward SS running the default 57.6K Baud. I even got an Ethernet breakout board and tried different configurations of the DMX to Renard SS Cable shown here as well as trying different F16V3 DMX/Renard Ports with different jumper & serial settings in the controller. Below is a link to a thread with some more info on this. The DYILEDExpress Bridge was mentioned by some other people in that thread and that solved ALL my issues so I'm just putting out some options for anyone who is not having good results with the DMX to Renard SS Cable.

http://doityourselfchristmas.com/forums/showthread.php?52590-F16V3-to-Renard/page5


Reply
Page 3 / 3
Share: