Falcon serial outpu...
 
Notifications
Clear all

Falcon serial output

28 Posts
8 Users
0 Reactions
16.4 K Views
Posts: 188
(@harpster)
Reputable Member
Joined: 17 years ago
Kev7274 wrote:Sorry for the delay. It's baud rate 19200 and stop bits 2. I'm in the process of doing run throughs to make sure things are ok. I guess I'm lucky since I have no delays running the Renard from the F16V3.

Thanks for the info! Maybe the lower baud rate is why your getting better results. I don't know but I've always run my Renard SS boxes at 57600. I think some people run it faster but didn't know it would work well at 19200. Probably related to the number of channels being driven and the event period (50ms I think, at least it was in Vixen 2.1).


Reply
duramadmax
Posts: 904
(@duramadmax)
Noble Member
Joined: 16 years ago
harpster wrote:Thanks for the info! Maybe the lower baud rate is why your getting better results. I don't know but I've always run my Renard SS boxes at 57600. I think some people run it faster but didn't know it would work well at 19200. Probably related to the number of channels being driven and the event period (50ms I think, at least it was in Vixen 2.1).

hmmm. Yeah my baud rate for the DIYledexpress bridge is 115k. Tried the same rate on the F16v3 and got the delay. didnt try the stock rate of 57600 because I didn't feel like reflashing the renard boards. SO is a lower baud rate the key? Curious on what ya find out...


Reply
Posts: 188
(@harpster)
Reputable Member
Joined: 17 years ago

I’m not going to use F16v3 for Renard Serial because at this point for me it’s more trouble than it’s worth. Even if running at 19200 baud worked on Falcon I think that data rate is too slow for my 100+ channels. Not to mention I would need to re-flash all my Renard SS boxes and test it.

Last season I ported my Vixen 2 sequences to Vixen 3 built RGB Snowflakes and Floods and integrated the F16v3 and Pi Player and that was taxing enough. I’m going to stick with the Bridge because worked flawlessly or I might use the Pi Player (RPi USB Port) which I tested at end of the season with good results. Those solutions for me are better than going through the F16v3 because I don’t trust it now for Renard but for Pixels it’s great!


Reply
TomL8345
Posts: 1356
(@toml8345)
Noble Member
Joined: 15 years ago
harpster wrote:I’m not going to use F16v3 for Renard Serial because at this point for me it’s more trouble than it’s worth. Even if running at 19200 baud worked on Falcon I think that data rate is too slow for my 100+ channels. Not to mention I would need to re-flash all my Renard SS boxes and test it.

Last season I ported my Vixen 2 sequences to Vixen 3 built RGB Snowflakes and Floods and integrated the F16v3 and Pi Player and that was taxing enough. I’m going to stick with the Bridge because worked flawlessly or I might use the Pi Player (RPi USB Port) which I tested at end of the season with good results. Those solutions for me are better than going through the F16v3 because I don’t trust it now for Renard but for Pixels it’s great!

I have gone the same route, using USB>RS485 adapter for Renards as opposed to running through my Falcon. Keep it simple.


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

Can I get a clarification? Are you running the Renards as "Renards" or as "DMX"?


Reply
Posts: 188
(@harpster)
Reputable Member
Joined: 17 years ago

I have only used Renard SS boards with the standard Renard firmware using 57600 baud rate.


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

Thanks. All of my Renard SS24s and SS16s are flashed with the DMX firmware. Didn't want to speak up if we weren't on the same page.


Reply
Posts: 9
(@justinmiller24)
Active Member
Joined: 6 years ago
Kev7274 wrote:i'll look to see what they are when I get home.

Hi Kev,

I am planning on running both pixel and AC lights this year and have a Falcon F16v3 and Renard SS24 similar to what you describe here. Aside from getting the setting updated (baud rate etc) is there a specific patch cable I need to use to go from the F16v3 serial port to the SS24? If so would you mind pointing me in the right direction?

I am prepare to make one if needed, but if there is an adapter or something off the shelf for this I would prefer to go that route instead. Please let me know.

Thanks so much!

Justin


Reply
TomL8345
Posts: 1356
(@toml8345)
Noble Member
Joined: 15 years ago

Justin,

Whether you need a specific patch cable for your setup depends on which firmware you have on your SS24. If you are running DMX firmware, you should be good to go, however, if you have Renard Firmware you will need to change the wiring either in a cable or adapter. There is a discussion on this topic currently going on at the Green Site. Post #6 in this thread shows you how to properly pin out the cabling.

It is much better to just make a short adapter with a male & female connection to keep with the controller. This allows you to use a standard ethernet cable rather than keeping track of a specific cable year to year.


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

I'm trying to find the actual wiring diagram we have used for years. It used to be on a wiki article on one of the DIYC sites, but I can't find it now. Anyone have it?

It is best to remember that the serial port wiring, sometimes marked as "DMX", and the DMX protocol are two different things. We send our data from the player to a controller such as the F16V3, then from its serial output to the string of SS16s and SS24s. The link from the F16V3 to the FIRST SS24 is "special". The links after that first SS unit, and between the remainder of the SS16s and the SS24s is standard cable (sometimes incorrectly referred to as "Ethernet") 568B wiring.


Reply
Page 2 / 3
Share: