10 2013 strips of ws2811 in pex, some have been on the house all year, 0 failures
10 new strips of ws2811 out in pex on the roof, garage etc, 0 failures
510 nodes of diyled express ws2811 nodes 1 color failure on 1 led, they have been out in the yard and rain about 3 weeks
850 Minleon bulbs strung 50' up in the air dangling from a tree in 16 strings, 0 failures.
Alan
I had 2 WS2811's fail this year. 1 had a hole in the weatherproofing (didn't notice the defect in that string) and the other likely got jostled around to much when connecting the string to power distribution.
My biggest problem this year is the dumb RGB strips that I added for the first time this year. They work great until the temperature gets to -23C and then random sections of 3 start going out intermittently. Once the strip is kept on for more than a few minutes or the temperature warms up the problem disappears. No issue with water as even the strips protected under the eves are doing the same thing.
If you had sections say small 3" sections out, would you replace that section or the whole strip? Some strings, none are out (most). Others there is one, maybe two sections (3") out.
RobertB wrote:If you had sections say small 3" sections out, would you replace that section or the whole strip? Some strings, none are out (most). Others there is one, maybe two sections (3") out.
Take CorrosionX and spray, or preferably inject, it into the lights from the out sections. If you catch it early enough (within 2 days) it works around 90% of the time to resurrect the out or misbehaving pixels.
2014
1100 12v 2811 bullets from diyledexpress
0 failures
150 v2 technicolor with c7 covers from Ray
0 failures
145 pixabulbs from diyledexpress 0 failures
4 6804 1st yr
0 failures
1 682 2nd yr
0 failures
5 miniren 8xb
3 or 4 dead channels
2014 Failures:
150 pixabulbs - 2, stay on green but pass data. 1, stays on purple but pass data. I will cut out and replace in off season.
150 square 12v ws2811 - Diyledexpress - 0 failures
300 bullet 12v ws2811 - Diyledexpress - 0 failures
50 HC Firepix (Technicolor V1) - 0 failures
2 5m RGB silicone encased strips (Not Sleeves) - 0 failures (2nd year)
6 - 6 led 5050 round 12v ws2811 from ebay - 0 failures (I encased in silicone in tree stars)
It's been a good year for the pixels.... GFCI's not so much 🙂
deonb wrote:Take CorrosionX and spray, or preferably inject, it into the lights from the out sections. If you catch it early enough (within 2 days) it works around 90% of the time to resurrect the out or misbehaving pixels.
That's interesting. Unfortunately they are on the roof for another 2 days and have been misbehaving now for a couple of weeks. These have been on the roof since beginning of Oct.
I have a few hundred of these from 2012 and 2013. They let water in around the LED/body joint so I now cover them with a C9 cover and they are okay, maybe two had problems this year in a rather wet Australian December.
http://www.aliexpress.com/store/product/12mm-8mm-led-pixel-RGB-led-channel-lettet-waterproof-WS2801IC-256-level-gray-scale-DC5V-input/701799_320389559.html
500 of these that I bought this year and were totally exposed to the elements with zero failures
http://www.aliexpress.com/item/50pcs-DC5V-input-WS2811-LED-pixel-light-with-all-BLACK-wire-IP68-rated-epoxy-resin-filled/1821855394.html
Jon
4000 Pixabulbs.. 8 lost color (red mostly).
I had a strip of about 25 that went out, but came back on later. When they were out they weren't that noticeable. Not anywhere close to as bad as the Technicolor issues I had last year.
Very happy with my decision to go with Pixabulbs. Todd was excellent about getting me up and running for my Halloween show.
in 2013 i switched over to pixels (95% from ray wu)
of the 8000 i had on my mega tree, 1250 failed in one way or another (HEREhe made them 2811 for me) plus about 700 more were DOA (wired backwards, or not even soldered).
then i got these little gems HERE, Oh MY GOSH what crap! i bought 1200 in 2013, at the end of the 2013 season (4 weeks of 4-6 hours a night) i had about 300 STILL WORKING.
so in 2014 i ordered these pixels strips HERE for my MTREE. except i made several changes BEFORE i would even order them.
the LEAD must be a 4 core FEMALE end wired to my specs
the END must be a 4 core MALE end wired to my specs (the 4 core because it will interface with ALL the controllers and existing wires that are in my display.)
I wanted them instead of 4 meters to be 3.5 meters (fit snuggly on a 10' PVC)
AND they must be QUALITY checked before leaving the plant. (he did all that for no additional charge, in fact each was a few dollars cheaper)
i have not had a SINGLE problem with the pixels.
now, having said that, the second order (for my arches) the plugs were on backwards... (but that was easily corrected by making a patch cable for those few)
the colors are all SPOT ON, they are crisp, clean, and look marvelous!
and at the end of the 2014 display, THEY ARE ALL STILL WORKING
I will order more (if funding allows) for 2015

