ESPixelStick Flash ...
 
Notifications
Clear all

ESPixelStick Flash Tool

223 Posts
49 Users
0 Reactions
100.2 K Views
Posts: 191
(@mlevings)
Estimable Member
Joined: 14 years ago

Any chance of getting a reverse option on the pixel output? I have a few places I could use these and a reverse output would be much easier than repatching my sequences.


Reply
Posts: 2048
(@scootchu)
Noble Member
Joined: 17 years ago

Just a report on how v2.0 and v2.1 are working. On my GECE's they have been running at about 98%. I have had to repower or reboot just a few times. On the Renard boards with either version I have been very happy with how stable they have been. And with 2811's attached, rock solid and no resets since turning off Mutlticast Enhancement on my Ubiquiti AP.


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

Ok guys,I have two questions.

(1) Who is actually getting an IP address in the serial output and not a bunch of jibberish?
(2) PLEASE tell me what programmer you are using?:wink:

Kind of annoying that I have to look into my router to see what IP address the modules are getting. I'm using the programmer and flashmaster from dirk.


Reply
Posts: 24
(@thomauto)
Eminent Member
Joined: 12 years ago

I get gibberish too, I have used two different cheap programmers not sure of the brand though. I always set a DHCP reservation for the sticks in the router so I have to go there anyway but if wanted to see the serial output i fire up monitor of the Arduino programer.


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago
Kev7274 wrote:Ok guys,I have two questions.

(1) Who is actually getting an IP address in the serial output and not a bunch of jibberish?
(2) PLEASE tell me what programmer you are using?:wink:

Kind of annoying that I have to look into my router to see what IP address the modules are getting. I'm using the programmer and flashmaster from dirk.

I use a 6 Pin, CP2102 (not the 5 pin cp2102, they don't work for me)
I do not use the Flashmater on the ESPixelStick, or the RP WiFiPixel,

ESPixelStick is the 3 wires from the CP2102, GRD Tx Rx, and separate 5V power to the board (normally, just USB power)
For the RP WiFi Pixel I use CP2102 GRD Rx Tx & 5V. The CP2102 will power the board.

Bought my first CP2101 from Dirk, but he was out of stock when I wanted a spare.
I bought my spare and a back-up spare from eBay. Here are Domestic & China links (China is for next year delivery)

California Stock: http://www.ebay.com/itm/1pc-USB-2-0-to-TTL-UART-6PIN-Module-Serial-Converter-CP2102-STC-PRGMR-/371046646242?hash=item56641a81e2:g:wvUAAOSw1XdUYHTD
Kentucky Stock: http://www.ebay.com/itm/1pc-USB-2-0-to-TTL-UART-6PIN-Module-Serial-Converter-CP2102-STC-PRGMR-/391631120172?hash=item5b2f08a72c:g:x0QAAOSwiDFYNTyD
China: http://www.ebay.com/itm/USB-to-TTL-UART-6PIN-Module-Serial-Converter-CP2102-STC-PRGMR-Free-cable-RX-/291929465379?hash=item43f85a2223:g:A5UAAOSwB09YF~1j


Reply
Page 12 / 45
Share: