i finaly succeed yesterday late ,,, i dont realy know what i did but it work ,,but i think it was because of the com port ,,i will try another tonigh
cheer
So I dug out my Bill Porter ESPixelStick GECEs and wanted see if firmware v3.0rc3 would work and low and behold it loaded and seems to work great! I did notice a few interesting side effects, however.
The configuration page isn't showing any values for anything when I load it using Chrome on a desktop PC. When using Chrome on my iOS device all the settings appear and I can configure the device. Also, on mobile when going to the Testing page and choosing a test that requires the RGB picker, there is no way to close the RGB picker and will overlay on the entire site unless I refresh the page. That's what I noticed.
I have tested with the LightsMaster iOS app that sends E.131 data from the phone to the ESPixelStick and it seems to receive data and work great!
adster wrote:So I dug out my Bill Porter ESPixelStick GECEs and wanted see if firmware v3.0rc3 would work and low and behold it loaded and seems to work great! I did notice a few interesting side effects, however.The configuration page isn't showing any values for anything when I load it using Chrome on a desktop PC. When using Chrome on my iOS device all the settings appear and I can configure the device. Also, on mobile when going to the Testing page and choosing a test that requires the RGB picker, there is no way to close the RGB picker and will overlay on the entire site unless I refresh the page. That's what I noticed.
I have tested with the LightsMaster iOS app that sends E.131 data from the phone to the ESPixelStick and it seems to receive data and work great!
Is your desktop PC Windows or Mac? Did you try any other browsers on it? I've had reports from a few other users, but haven't been able to consistently re-produce it. There's an issue filed on it here - https://github.com/forkineye/ESPixelStick/issues/65 . It's pretty much the only thing holding up 3.0 final at this point.
thanks,
-shelby
sporadic wrote:Is your desktop PC Windows or Mac? Did you try any other browsers on it? I've had reports from a few other users, but haven't been able to consistently re-produce it. There's an issue filed on it here - https://github.com/forkineye/ESPixelStick/issues/65 . It's pretty much the only thing holding up 3.0 final at this point.
thanks,
-shelby
So I just flashed another 25 count ESPixelStick GECE and it also works great. I get those interface problems on this second one also.The problems happen using the latest Chrome on Windows 10, Edge browser on Windows 10 and on the latest Chrome on my iMac. I just tried all 3 and they're all displaying the problem. Thanks shelby!
Sometimes I just close the browser, clear the cache and that clears the issues with the UI.
Sent from my SM-G930V using Tapatalk
adster wrote:So I just flashed another 25 count ESPixelStick GECE and it also works great. I get those interface problems on this second one also.The problems happen using the latest Chrome on Windows 10, Edge browser on Windows 10 and on the latest Chrome on my iMac. I just tried all 3 and they're all displaying the problem. Thanks shelby!
So is this "new" firmware for the ESPixel GECE approved or is an approved in the works still?
duramadmax wrote:So is this "new" firmware for the ESPixel GECE approved or is an approved in the works still?
Not sure if it's approved or not, bit I know in the original ESPixelStick GECE thread, Bull Porter mention the firmware was based on sporatic's firmware. I know a lot of people couldn't get 2.0 or 2.1 to work (I didn't even try it) but today I just decided what the hell and took out my GECE's and threw on the firmware. It accepted the firmware flash, connected to my Wireless network and started accepting data so as far as I know, it works great. Haven't tested for long periods of time, but I did leave it running for 2 hours or so. Didn't even have to mess with the Arduino stuff anymore, I just used the built in ESPixel Flasher utility hat came with the firmware. No errors at all.
hmmmm might have to give it a whirl. Any benefit to upgrading it that you know of?
duramadmax wrote:hmmmm might have to give it a whirl. Any benefit to upgrading it that you know of?
The interface is completely different. There's a ton more testing options, including a full color picker and chase sequence to test the strand. I'm just hoping it'll fix the problem I had with the 1.4 firmware where it wouldn't reconnect to the router if there was a network hiccup. That would leave my GECE strands dead pretty regularly last season, so much so they I used a smart switch ti disconnect and reconnect the power throughout the evening to prevent it from happening.
adster wrote:The interface is completely different. There's a ton more testing options, including a full color picker and chase sequence to test the strand. I'm just hoping it'll fix the problem I had with the 1.4 firmware where it wouldn't reconnect to the router if there was a network hiccup. That would leave my GECE strands dead pretty regularly last season, so much so they I used a smart switch ti disconnect and reconnect the power throughout the evening to prevent it from happening.
I used Shelby's latest code last year and had far fewer problems with my GECE's. I will have to do a test with a set this weekend.
