ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.7 K Views
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

So the flicker was caused by a delay in the datastream over the network?

davedecali wrote:Took the Renard pixel stick off the main home wifi network and placed onto "guest" network the Apple router had to limit cross traffic... checked voltage off board at 12V and viola no more flicker sending E131 from FPP

Sent from my iPhone using Tapatalk


Reply
Posts: 98
(@davedecali)
Estimable Member
Joined: 10 years ago

Mine was yes... I am not sure about the other flicker from kev... that looked hardware related... mine was def more of a pulse associated with a refresh... running nice and smooth now

Sent from my iPhone using Tapatalk


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
kev wrote:New pixels. Pixels work on other ESPixelsticks. Firmware 2.0. Pi-3 with FPP hardwired to router. Other 9 ESPixelsticks worked OK.

Can you try the 3.0dev1 firmware? Some newer pixels require different timing and 3.0 implements it.
thanks,
-shelby


Reply
Posts: 98
(@davedecali)
Estimable Member
Joined: 10 years ago

Received the Amazon ESpixel from Shelby and this one wins by a lot. First off I was able to power 500 pixels off a 60w 12v supply with minimal dimming at full white which I think is pretty amazing. I know it can do 4 universes but 500 covers most of my props.

Sent from my iPhone using Tapatalk


Reply
Posts: 1387
 kev
(@kev)
Noble Member
Joined: 12 years ago
sporadic wrote:Can you try the 3.0dev1 firmware? Some newer pixels require different timing and 3.0 implements it.
thanks,
-shelby

I will try it, but as I mentioned, the problem follows the ESPixelstick main board, not the ESP-01 module. Will post results a little later.


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

Yeah,these are great.
Being able to get them from Amazon is excellent for those who just want to get them and start using them instead of soldering.

davedecali wrote:Received the Amazon ESpixel from Shelby and this one wins by a lot. First off I was able to power 500 pixels off a 60w 12v supply with minimal dimming at full white which I think is pretty amazing. I know it can do 4 universes but 500 covers most of my props.

Sent from my iPhone using Tapatalk


Reply
Posts: 92
(@adster)
Estimable Member
Joined: 11 years ago

Has anyone installed the newer firmware on the ESPixelStick GECE version by Bill Porter? I remember reading some people had problems with the 2.0-ish firmware and just wanted to see if anyone else has tried it lately. I may dig them out and try myself.

Sent from my iPhone using Tapatalk


Reply
Posts: 98
(@davedecali)
Estimable Member
Joined: 10 years ago

I flashed with the new firmware with no issues ... the Renard ESpixel had mixed results on showing the IP once programmed but all got sorted once the IP address was located through Fing

Sent from my iPhone using Tapatalk


Reply
Posts: 1387
 kev
(@kev)
Noble Member
Joined: 12 years ago

Downloaded 3.0dev1 firmware and the flickerig is still occurring. The problem follows the board. No big deal, that is why I bought a couple of extra.


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
kev wrote:Downloaded 3.0dev1 firmware and the flickerig is still occurring. The problem follows the board. No big deal, that is why I bought a couple of extra.

I'll replace it. Would like to do some analysis on it though to see what the issue is as it's a first. PM me your address and I'll get one out to you tomorrow.

Sent from my R1 HD using Tapatalk


Reply
Page 62 / 95
Share: