Pixel stick knows nothing about the folding (aka zig-zag) implemented by your lights. For the pixel sticks you do all of the zig-zag work in your sequencer / player. It all looks like one long string to the pixel stick.
It looks like I am late to the party for the GB of the ESPixelstick so I attempted to put the sketch on an ESP8266 I have to test with; but I have a problem that I hope someone can send me in the right direction to get a solution...
I followed the directions to install on the ESP8266, and located and added libraries as required to compile without error, namely ArduinoJson-master, ESPAsyncTCP-master and ESPAsyncWebServer-master
The Serial output shows:
ESPixelStick v2.0 alpha
- Configuration loaded.
Connecting to
Connecting with Static IP.............
Connected with IP: 192.168.1.204
- Unicast port: 5568
- Web Server started on port 80
- Listening for 1 channels, from Universe 1 to 1
I can ping the IP address but when I access with any browser there is nothing returned.
Without logs or errors, I don't know where to look.
TIA for any help with this 🙂
PB
You missed the step in which the web pages are uploaded to the ESP. Web pages are now in the spiffs instead of compiled into the code.
Easier to use the flash tool that sporadic posted here.
https://github.com/forkineye/ESPixelStick/releases/download/v2.0/ESPixelStick_Firmware-2.0.zip
EDIT link to latest 2.0 version
Thank you. I was following the original steps with the new code. duh.
I did manage to install v1.4 with no apparent issues and have been testing in this new environment.
I'll try the v2.0 later in the week.
Thank you for your help
PB
I seem to have missed the boat. Is it possible to get one or two of these wifi pixel controllers?
I need some help getting the firmware loaded.
I have never loaded any Arduino software, so none of the IDE is installed (yet). I was thinking the new V2 flash tool ( https://github.com/forkineye/ESPixel...rmware-2.0.zip ) did not need anything else. Is that true?
I'm using a CP2101 USB breakout. If I try to upload using the Flash Tool it gives this error
I have been attempting to put it in programming mode by pressing/holding the "PROG" button and then clicking the "RESET" button and then releasing "PROG". The Serial Output screen shows a short line of jibberish (like the baud rate is wrong). I have set the baud rate to 115200 as per instructions. Also I have tried connecting to the same com port with TerraTerm (serial terminal emulator) and when the ESPixelstick powers up it displays:
Ai-Thinker Technology Co. Ltd.
ready
I can type characters and they echo back so this makes me believe the USB-Serial interface is working ok. But I've tried some random AT commands and never get any response back (just the characters echoed back)
I have tried this on two new ESPixel sticks and its the same on both. What am I missing here?
I got my 15 kits today! Break out my soldering station and start getting these ready for my show.... Excited!!! Thanks Shelby!!!
timstreet wrote:I seem to have missed the boat. Is it possible to get one or two of these wifi pixel controllers?
I'm looking at making more available in October as time permits.
pixelpuppy wrote:I need some help getting the firmware loaded.I have never loaded any Arduino software, so none of the IDE is installed (yet). I was thinking the new V2 flash tool ( https://github.com/forkineye/ESPixel...rmware-2.0.zip ) did not need anything else. Is that true?
I'm using a CP2101 USB breakout. If I try to upload using the Flash Tool it gives this error
I have been attempting to put it in programming mode by pressing/holding the "PROG" button and then clicking the "RESET" button and then releasing "PROG". The Serial Output screen shows a short line of jibberish (like the baud rate is wrong). I have set the baud rate to 115200 as per instructions. Also I have tried connecting to the same com port with TerraTerm (serial terminal emulator) and when the ESPixelstick powers up it displays:
Ai-Thinker Technology Co. Ltd. readyI can type characters and they echo back so this makes me believe the USB-Serial interface is working ok. But I've tried some random AT commands and never get any response back (just the characters echoed back)
I have tried this on two new ESPixel sticks and its the same on both. What am I missing here?
That's all you need to do. Once you get the line of jibberish, it should be ready to program. In the status window, there should be a line that says "-= Programming ESP8266 =-". Can you post everything after that?
sporadic wrote: In the status window, there should be a line that says "-= Programming ESP8266 =-". Can you post everything after that?
This is what I get..
-= Programming ESP8266 =-
bin/win/esptool.exe -cd none -cb 115200 -cp COM3 -ca 0x000000 -cf firmware/pixel-2.0-1m_128k.bin -ca 0xDB000 -cf firmware/spiffs.bin
Uploading 315392 bytes from firmware/pixel-2.0-1m_128k.bin to flash at 0x00000000
warning: espcomm_send_command: didn't receive command response
warning: espcomm_send_command(FLASH_DOWNLOAD_BEGIN) failed
error: espcomm_upload_mem failed
PROGRAMMING FAILED

