its been a while but i finally continued my project. i got it running in jinx! but still got a big delay. is this because i directly send the data from gpio2 to the led strip ?, instead of using the board wich sends it thru the 74VHC1G ( wich boosts up the voltage of the data signal from 3.3v to 5v, am i right ?)
Not sure what type of delay you are talking about. Skipping the output driver would not "cause" a delay. It might cause flickering or other unwanted effects but not "delay". Adding the buffer / driver may cause a few nano-seconds worth of delay, not worth talking about. If by delay you mean that some floods are out of synch with other elements in your display, then that is most likely a networking issue. Keeping things in sync is about the only (this is my personal opinion as a person that avoids using multicast in his show) reason I would use multicast E1.31 and have all of the floods driven in a single universe. You might also look into the device creating the E1.31 data stream. It may be having issues getting the Ethernet packets sent in a timely manner.
dylangelaan wrote:its been a while but i finally continued my project. i got it running in jinx! but still got a big delay. is this because i directly send the data from gpio2 to the led strip ?, instead of using the board wich sends it thru the 74VHC1G ( wich boosts up the voltage of the data signal from 3.3v to 5v, am i right ?)
Is your source / jinx running wireless as well on the same AP? This is a common mistake many make and will cause all sorts of issues due to the simplex nature of wifi.
Sent from my XT1094 using Tapatalk
sporadic wrote:Heyas everyone. Sorry, been away for a while due to work and other life stuff. I have the new boards laid out and almost ready to be sent off (silkscreen and tweaks to be done), just need to wrap up a few things at home before I can get back to working on this. Biggest change is an onboard switching converter, allowing for 5-24V input without having to deal with a configuration jumper and alternate mounting option for people who stick these in CG cases.
Looking for any more beta breakers? Or are these getting close to being released into the wild through store/group buy?
thanks for replying 🙂
@ sporadic, you mean if i connected my laptop sending data from jinx with a network cable to my router ? if yes, i tried that ass well..
i think one off my setings is just wrong, i get only like a frame per second with a delay of aproximitly a seccond as well .no matter what i tried(so far). its kind off hard to describe my problem to you but il try my best since there are so many devices(3) that all have possible settings.. the software sending the data signal, the router recieving and sending the data, and the pixelstick recieving data. I tried my best trail and erroring but without succes.. so i help you guys can tell me what else i can try or need to do 🙂 it will be so nice iff it finally works proper 🙂
things i tried hardware wise ; made different boards, tryed multiple esps, multiple routers (wired and wireless conected to my laptop)
things i tried setting up JINX (wired to router and wireless, no difference in frame rate or dely detectable..,);
-multicast ( works, but delay low framerate)
-single cast,sending to fixed ip set up in the pixel stick
-router dhcp on/ of
-esp pixelstickk dhcp on/of
-and more..
i also tested it with luminair, (software only uses multicast so i dont know if it will ever run smoothe..) wich worked but gave me the same low framerate and delay.
maybe its just me being dumb not knowing how u setup a fixed ip network on the router?!
what does man need to fill in in the configuration of the pikselstick besides an ip adress? as ip i putted down 192.168.2.11 i tried putt some things down at gateway and add the subnett such as 255.255.255.0 for subnet and gateway 192.168.2.1 (the same adress as my router) it seemed to work (still same problem)but i dont know if that is the way you should do it..
if i send data via artnet to a dmx to spi converter i have no delays, high framerates and everything works great, so i thought the network settings must be also ok for sACN ?!
i hope my all my data can give u guys a cleu what i might be doing wrong, thanx for ur time graets Daan!
thanks for replying 🙂
@ sporadic, you mean if i connected my laptop sending data from jinx with a network cable to my router ? if yes, i tried that ass well..
i think one off my setings is just wrong, i get only like a frame per second with a delay of aproximitly a seccond as well .no matter what i tried(so far). its kind off hard to describe my problem to you but il try my best since there are so many devices(3) that all have possible settings.. the software sending the data signal, the router recieving and sending the data, and the pixelstick recieving data. I tried my best trail and erroring but without succes.. so i help you guys can tell me what else i can try or need to do 🙂 it will be so nice iff it finally works proper 🙂
things i tried hardware wise ; made different boards, tryed multiple esps, multiple routers (wired and wireless conected to my laptop)
things i tried setting up JINX (wired to router and wireless, no difference in frame rate or dely detectable..,);
-multicast ( works, but delay low framerate)
-single cast,sending to fixed ip set up in the pixel stick
-router dhcp on/ of
-esp pixelstickk dhcp on/of
-and more..
i also tested it with luminair, (software only uses multicast so i dont know if it will ever run smoothe..) wich worked but gave me the same low framerate and delay.
maybe its just me being dumb not knowing how u setup a fixed ip network on the router?!
what does man need to fill in in the configuration of the pikselstick besides an ip adress? as ip i putted down 192.168.2.11 i tried putt some things down at gateway and add the subnett such as 255.255.255.0 for subnet and gateway 192.168.2.1 (the same adress as my router) it seemed to work (still same problem)but i dont know if that is the way you should do it..
if i send data via artnet to a dmx to spi converter i have no delays, high framerates and everything works great, so i thought the network settings must be also ok for sACN ?!
i hope my all my data can give u guys a cleu what i might be doing wrong, thanx for ur time!
Wolfie wrote:Looking for any more beta breakers? Or are these getting close to being released into the wild through store/group buy?
Not yet, waiting for my new soldering station to get in. My trusty 25yr old Weller died on me while building the prototypes.
sporadic wrote:Not yet, waiting for my new soldering station to get in. My trusty 25yr old Weller died on me while building the prototypes.
Rip sir. I feel your loss. 😉 My +30yr old Micronta (radio shack) multi-meter died a horrible death last year (battery acid leak). Probably should have changed the battery more than once per decade huh?
New station showed up, so I'm back at it! Power supply section on the new design is looking good so far. Two more to build out and more testing to be done, but it's looking good. I've been working on the new frontend for the web config as well, but it's not in the repo yet. First phase will be porting the current code to an asynchronous web server, then implementing the new frontend.
The new web front end is designed more like an e1.31 to anything router, to be easily extensible and supporting more than just the ESPixelStick hardware. Just a sneak-peak:

