ESPixelStick - E1.3...
 
Notifications
Clear all

ESPixelStick - E1.31 WiFi Pixel Controller

948 Posts
178 Users
0 Reactions
503.7 K Views
Posts: 204
(@m1anh)
Estimable Member
Joined: 12 years ago
kwoodard wrote:I'm looking at creating a through-hole version of the ESPixelStick since I have most of the components on hand. The two main differences between my board layout and sporadic's layout involves the voltage regulators and the line driver. For the voltage regulators, I'm looking at using a LM7805 for the 5V regulator and a LM1117T for the 3.3V regulator. For the line driver (to convert the data signals from 3.3V to 5.0V), I'm looking at using a simple 2N7000 MOSFET circuit like is shown at http://www.hobbytronics.co.uk/mosfet-voltage-level-converter .

After studying the circuit, I must say that I'm super impressed with the design.

Before I get some PCBs made, does anyone see any issue with this approach? The PCBs turn out to be not much larger than the SMT version, but I'm adding mounting holes. I plan to mount these inside a waterproof enclosure next to a power supply; therefore, I'm not as concerned about the small footprint.

Maybe a silly question but Why?, You can download and buy Sporadics version Here.., for the sake of a few SMT parts.
I built my own, but for a different reason. I had already a design similar to Sporadics, but using the ESP8266-03 SMT Module, I had 10 in hand.

If you want a very simple 3V to 5V level shifter why don;t you use this: Poor mans Level Shifter..Click Here.. Figure 7.1.

Its 2 diodes and a resistor. It works for me.

As for the DC-DC Converter, I use the KIM-055L, I have 10 of these in operation, I am driving a 150 Pixel Tape without an issue. (Although I would not leave then on 100% to too long.)

ESPPixelBug Pics
ESP DC DC A 101 6248x

Reply
Posts: 911
(@madsci1016)
Noble Member
Joined: 12 years ago

I did testing with the diode method early in the year. It did not work reliably, especially with GECEs. I do not believe some of the cheap pixel chips are built to TTL specs.

Sent from my SM-T700 using Tapatalk


Reply
kwoodard
Posts: 281
(@kwoodard)
Reputable Member
Joined: 13 years ago
m1anh wrote:Maybe a silly question but Why?, You can download and buy Sporadics version Here.., for the sake of a few SMT parts.
I built my own, but for a different reason. I had already a design similar to Sporadics, but using the ESP8266-03 SMT Module, I had 10 in hand.

No silly questions :). I've never soldered SMT parts and wanted a version that I felt comfortable building. I also like to be able to build more boards on an as-needed basis; therefore, having to wait for a group buy led me to make my own version. That's the beauty of open source hardware design - I wanted a through hole version and could build upon sporadic's design for my version. I'm really excited about the possibilities of these ESP based designs. Sporadic has done a fantastic job with this design concept!


Reply
Posts: 204
(@m1anh)
Estimable Member
Joined: 12 years ago

I've never soldered SMT parts and wanted a version that I felt comfortable building. I also like to be able to build more boards on an as-needed basis; /QUOTE]

Are you planning to etch the pcbs yourself? Because I believe you can order the PCBs yourself without waiting for the group buy. I find SMT much easier than PTH, you just need some tweasers, small soldering iron tip and fine solder. A microscope helps if your eye site is not to good. I wanted some PCBs ASAP, hence the etching of my own PCBs. If you are only using only 5V pixels, you do not need the 7805.
I have not had any issues with the Poor man's level shifter, but the value of the resistor needs to be right, although I have only tested it with WS281x. So not seen the issues Bill has.

Sent from my HTC One S using Tapatalk


Reply
Posts: 499
(@frederic)
Honorable Member
Joined: 14 years ago

This I'm sure will be the stupid question but I'm going to ask it anyway.

For those of us with an ESP-01 USB programmer on the way that's separate and stand-alone, all we'd need to make the minimal functionality is the ESP-01, the 3.3V regulator, a logic voltage shifter, and the reset button?

Thanks for the input!


Reply
Posts: 39
(@toottime)
Eminent Member
Joined: 11 years ago

Anyone Care to share pictures of how they mounted there ESPixelStick's to there display elements waterproofing ideas ect

An idea I have is to mount the stick in a waterproof junction box with pigtail leads for in/out power few concerns are if I may lose the signal strength being in a junction box and if the pigtail connecters from ray are waterproof ?

Thanks


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
frederic wrote:This I'm sure will be the stupid question but I'm going to ask it anyway.

For those of us with an ESP-01 USB programmer on the way that's separate and stand-alone, all we'd need to make the minimal functionality is the ESP-01, the 3.3V regulator, a logic voltage shifter, and the reset button?

Thanks for the input!

Pretty much. In some cases, you could eliminate the level shifter and drive the pixels straight off the ESP pin. I did this in development with a NodeMCU board, but I wouldn't recommend it for your show.

Toottime wrote:Anyone Care to share pictures of how they mounted there ESPixelStick's to there display elements waterproofing ideas ect

An idea I have is to mount the stick in a waterproof junction box with pigtail leads for in/out power few concerns are if I may lose the signal strength being in a junction box and if the pigtail connecters from ray are waterproof ?

Thanks

I use 1" thinwall PVC for mine, drill one of the caps, and silicone. Then they're zip-tied to the elements or to a clip for mounting. These are my previous nRF based modules, but I used the same cases and pigtails for my ESPixelSticks this year. Note the XT-60 connectors I use for power aren't waterproof. I give them a healthy dosage of liquid electrical tape and dialectric grease.

IMG_20141124_215102 by smerrick, on Flickr


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I use a heavy duty freezer bag zip tied to my pvc with the open end down. Works like a charm.


Reply
Posts: 240
(@lowepg)
Reputable Member
Joined: 13 years ago

Please count me in when you re-run these in 2016. PS Id LOVE to get my hand on one before our local area synchronized lighting group meets in mid February!


Reply
Posts: 499
(@frederic)
Honorable Member
Joined: 14 years ago

I was curious, if any of you have a link to a noob-level guide that shows how to set up the proper environment for compiling the git source for ESPixelstick, and load it into the ESP-01. I would prefer Windows x64 but can use linux (centos 6) if I have to.

I've looked at several guides/howto's on the web but they're different enough to where they as a collective are confusing me. One talked about a lauloader bootstrap and another talked about nodeMCU and I'm a real noob when it comes to programming tiny things. I'm going to have to do this for PICs too as I have a box of 16F1825's coming.

I bought a dedicated ESP-01 programmer for $9 on ebay (pic attached) to make life easier. It plugs into a USB port and has the correct voltages, and the CH340 supposed to be supported by Windows of all flavors, including x64 and Win10. Drivers are included in the auction.

Thanks for any points in the right direction.

EDIT: Nvm, I read the PDF for ESPixelstick and it included instructions for noobs 🙂

esp programmer

Reply
Page 10 / 95
Share: