ESPixel Pops laggin...
 
Notifications
Clear all

ESPixel Pops lagging

14 Posts
6 Users
0 Reactions
3,802 Views
CUTTHEMUSIC
Posts: 51
Topic starter
(@cutthemusic)
Trusted Member
Joined: 14 years ago
[#53047]

Over the last few years I ran 11 ESPixelSticks which each have 98 pixels. All 11 are all set to the same universe so that the 11 props do the exact same thing and I ran them off of an old Linksys router without any issues. This year I am adding 9 new PixelPop. Each PixelPop is attached to an independent prop with 365 pixels. This year I have upgraded my wifi to a nano station that I have dedicated to my show network. I have no other devices beside the ESP pops connected. I followed this thread to setup the nano. https://diychristmas.org/vb1/showthread.php?8693-Nanostation-Settings&p=95821&viewfull=1#post95821
My universes are pretty much packed together so that I am not wasting channels. I also followed most if not all of the suggestions found here. https://www.diychristmas.org/wiki/index.php?title=Streaming_ACN_over_WiFi . including setting the mcast_rate to 24000 iwpriv ath0 mcast_rate 24000 (I am aware that this setting does not persist on power down). Setting the mcast rate to 24000 made things better but there is still a very apparent lag. I also tried setting the mcast rate to 12000 and 36000 but 24000 seemed to give me the best results but still not anywhere close to perfect. For my show PC I am using LOR S5 on a decent laptop (I7, 8GB ram, SSD). The pc is dedicated to controlling lights and the wifi adapter is turned off. The nano station is connected directly to my pc via the ethernet port. I have all of my PixelPop set to multicast. The strange thing is that I am getting random lagging. The song will always start off exactly on queue but then quickly falls behind. Then sometimes catches up only to quickly fall behind again. If I only connect 3 of the props then the timing seems to be perfect. After connecting a few more the lag gets worse and worse. I've moved the nano station around, changed the channels from auto to whatever other options are available and nothing seems to help. I have a high quality cat6 cable connected to the nano station and I tried moving the POE injector closer to the nano station and nothing helped. The 5v meanwell power supply and PixelPop are in enclosures that I 3d printing using black PLA filament. I guess the next thing I should try is removing the PixelPop from the PLA enclosure to see if that helps. Other than that I feel like I am about ready go back to using some sandevices units that I have. Please let me know if you have any suggestions. I am very frustrated and have been at this for 5 days. Thanks in advance.


13 Replies
DrNeutron
Posts: 2016
(@drneutron)
Noble Member
Joined: 14 years ago

Since this worked fine with the old Linksys router, I would try this:
-Take old Linksys and disable wifi on the router
-setup a small DHCP range on router, I have this as my ESPIXELSTICKS use DHCP.
Now plug your computer into router and the Nano into the router and try running your show.
You didn't say what version of the firmware you are running (assuming 3.x).
Have you tried logging into Pixelsticks to see if there are errors?


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

I agree with checking the error logs on the pixelpops.
When you run only 3 pixelpops and things are okay, have you tried moving those three around?
Seems to me that would tell you if you have a reception issue or not inside the 3D printed cases.
I'm guessing that won't make a difference, which says you have a networking issue.


Reply
CUTTHEMUSIC
Posts: 51
Topic starter
(@cutthemusic)
Trusted Member
Joined: 14 years ago

I have a edgerouterx setup as a switch. What is the purpose of adding a router in between the pc and nano station? I have to check but I think I’m running 3.? esp firmware. I set them up about 3 months ago. I have logged in and I see errors that appear to be 5-10% of packets received. Not sure if that is acceptable.


Reply
CUTTHEMUSIC
Posts: 51
Topic starter
(@cutthemusic)
Trusted Member
Joined: 14 years ago
ukewarrior wrote:I agree with checking the error logs on the pixelpops.
When you run only 3 pixelpops and things are okay, have you tried moving those three around?
Seems to me that would tell you if you have a reception issue or not inside the 3D printed cases.
I'm guessing that won't make a difference, which says you have a networking issue.

When you say logs do you mean the error count on the first page of the pixel pop admin page or are there logs on the nano station?


Reply
Page 1 / 3
Share: