Did you see the 2 supply examples in the wiki power injection article?
@ http://www.doityourselfchristmas.com/wiki/index.php?title=Power_Injection#Multiple_Power_Supply_Injection
Note: There seems to be debate whether power line should be broken before each injection.
ref: http://doityourselfchristmas.com/forums/showthread.php?37027-e682-max-pixels-per-port&p=362903#post362903
Micromutt, Those examples are for when you have a long distance to the first pixel or need to inject power downline. The example we are talking about here is using two power supplies with one E682 with all connections directly from the E682 with no power injection using 12V pixels.
You do not need fuses if you are connecting both 350W power supplies to the E682, both side of the E682 has a 30 amp fuse at the power connector. You are primarily connecting the two grounds (Green wire in most cases just to prevent an impedance mismatch I believe.)
Xenia wrote:The example we are talking about here is using two power supplies with one E682 with all connections directly from the E682 with no power injection using 12V pixels.
I'm also trying to figure out my power supply needs for a 32 string (50up/50down) mega tree. So, can I run 100 pixels on each of the E682's 16 connectors and use 2 of the standard 30A power supplies connected directly to the E682?
You're right. I confused myself since the topic went from 'what power supply' to 'power injection' then to '2 supplies no injection'. :zipped:
gassy wrote:So, can I run 100 pixels on each of the E682's 16 connectors and use 2 of the standard 30A power supplies connected directly to the E682?
Probably not. It depends on what your power draw is per string.
3 amps per 50 pixels (12 volt) seems to be a common, safe number (though it seems nobody really knows the exact numbers). If you did two strings per connector, this is maybe 6 amps, and each port on the E682 is fused for only 5 amps.
I, however, am looking as I type this at a string of 100 bullet pixels (supposedly 60ma each, so 6 amps total) set all white off one data port (without injection, though with a short wire run) and it works great. I, however, think you'd be much better injecting power (can use the same power supplies) at the end of each 100 string run to be safe.
The other consideration is the total amperage. With 1600 pixels at 60ma each, that would be over 90 amps (45 on each side), well above the capacity of your power supplies. And the E682 is rated at 40 amps (I think) and fused at 30 (per side). So that's not likely to work, I think. You'll want at least one and probably two additional power supplies to power 1600 pixels (assuming 60ma per pixel).
Here are how my E68x's are wired up. I run 5 volt pixels. Two power supplies, each one running one side of the board. I have run 50 gece's on all 16 connectors with no problem. I do inject power from the same port to the end of the string as safe bet so
I do not get "pinking".
So I run a data line, ground, and one power wire to beginning of string then put another power and ground wire to end of string. I also run a common ground buss to tie all ground together. The power supplies are 7.5v units turned down to about 5.9 volts.
Xenia wrote:I think this is what you are referring to, two power supplies, no injection.
Not complaining or anything, just looking for clarification. The diagram says the first Bank1 runs strings (1-6) and Bank2 runs strings (7-16), but there are 8 banks on each side. Should that be (1-8) and (9-16)?
For me, i will only be running 16 strings this year, this was a big help to clarify.
That's a big help for me too guys, I'm going pixels next year, gonna try and squeeze 16 strings of 100 5v pixels up and over and insert power at far end. My approach is going to be load it up on a bench and see if the 30amp ( maybe put a smaller fuse in first and ramp up the colours) fuse will hold before I work out my spacing, if not I'll just take the pixels count down 10 at a time until it dose. I'll let you know my findings later on in the year, gotta earn some penny's to buy the pixels first.



