I see that the E682 has two power input connections. If I use two 12 volt 30 amp power supplies will I be okay to power 1350 rgb pixels?
I saw somewhere on the forum it was .06 amps per pixel. Is that for each total pixels and not time three for RGB?
.06 amps per pixel X 1350 = roughly 80 amps.
How do I get the a third power supply to the pixels or do I inject the power somewhere?
Thanks
Covewi
I'm working on what you're working on!
covewi wrote:I see that the E682 has two power input connections. If I use two 12 volt 30 amp power supplies will I be okay to power 1350 rgb pixels?
Yes, but it depends how you hook them up. The E862 has a 5amp fuse on each of the 16 outputs.
I see two concerns:
1) If you run 83 bulbs max per output, no problem. ( that only equals 1,328) Any more and you might blow a fuse.
2) Two power supplies, 30 A each=60A 60A÷.06A per pix =1000 pix 1000pix÷16 outputs= 62 .5 per string. 62Pix X 16 outputs= 992 pix
I saw somewhere on the forum it was .06 amps per pixel. Is that for each total pixels and not time three for RGB?.06 amps per pixel X 1350 = roughly 80 amps.
This is the same math that I am using. I believe you are correct. I hope you are correct.
How do I get the a third power supply to the pixels or do I inject the power somewhere?Thanks
Covewi
To answer your last question it would help to see how you are laying out your strings. Can you post a diagram?
Program your power consumption. This is not covered very often, but when power is limited, most forget that pixels that are not on draw very little power.
It is possible to create sequences where all pixels all white is never used. This will limit your power requirements. All white rushing across a display is impressive, but if 3/4's is black during the sweep, your power draw is about 1/4 the all on white power draw.
Chasing mini trees or candy canes? Leave 1/2 black at any one time and your power draw is 1/2 the max possible power draw.
Get creative if you are limited.
Good luck. Do you have everything on in any of your sequences?
I do the same thing with stage lighting with 1,000 watt spots. If I want the stage RED, the White spots are off. They are never both on at the same time.
For amature operators, the colors are programmed to null channels, but for a special, they are added and only experienced light jockeys that understand the power limitation is permitted to operate the console for the big productions.
This by the way is why big concerts have lighting engineers and operators. Power for big shows is always a challenge. Done wrong, it is a disaster. Some wedding DJ's with portable light shows find this the hard way as many outlets are on the same breaker as the sound system. A proper power survey is a requirement for any professional show. Every watt is mapped to a breaker.
I've only tripped breakers in the pre show testing to find the capacity and where unknown, what outlets are shared with the ice machine in the kitchen. True, story. Outlets for the ice machine were on the same breaker as outlets in a gym.
If your maximum light capacity exceeds your supply capacity, sequence so the total on capacity is less than the supply capacity.
My matrix is 27 rows high X 50 pixels wide.
Was planning on 9 strings each having 3 stands of 50 (150 pixels per string)
Thought it would work out nice and even. Plugging 9 strings into 9 outputs. Doesn't look like this will work.
Can I still have this matrix configuration and break up the number of pixels in within a row?
If you don't think this will work can you offer up suggestions?
Iam totally new to this and can certainly use a little guidance.
Thanks
You can power the pixels directly from a power supply and only send the data from the E682 as well just be sure to put inline fuses.
covewi wrote:My matrix is 27 rows high X 50 pixels wide.Was planning on 9 strings each having 3 stands of 50 (150 pixels per string)
Thought it would work out nice and even. Plugging 9 strings into 9 outputs. Doesn't look like this will work.
Can I still have this matrix configuration and break up the number of pixels in within a row?If you don't think this will work can you offer up suggestions?
Iam totally new to this and can certainly use a little guidance.
Thanks
I don't know about breaking up pixels in the middle of a row I believe you could buy cutting the wires. Someone else will have to chime in on this.
I like running one string out and one string back. You can add power to the end easily that way. (Less wire.) All controllers and power supplies would be together.
For some strings, I've hardwired the wall wart power supply for DJ type lighting. The wall wart powers 1 string. Only Ground and Data is fed from the controller. Works like a charm. Add a string? Not a problem. Mixing 5V and 12V pixels on the same string? Not a probllem. Each string is mated to the proper supply to run it. Only data needs to be run from string to string or controller to strings.
In an event tent or gym, it is often not difficult to find local power around the perimiter where the lights will be installed. Changing show size is easy this way. Even 12V battery power is possible on the bridge and wireless router if you use one if you want to do a Disney style parade and have everything sync.
Hey, that plastic matrix backing looks familiar to me…
Looking good!
ArcadeNut wrote:You can power the pixels directly from a power supply and only send the data from the E682 as well just be sure to put inline fuses.
I will need to power the pixels directly - not through the e682 - it will just work out better this way.
So I only need to send Data - from the e683 (just one wire) - and then send the 12 volts and the GRND from the external power supplies to the pixels?
Does this sound correct?
Thanks
