budude wrote:You do *not* count null pixels at the sequencer level - - that's really the whole point of having them as 'null' vs a plain 'ol unused pixel...Just want to be sure you realize that you'll need power injection with longer strings. With 12v pixels you can probably go about 100-ish before needing injection - maybe more - maybe less - YMMV
Yep. I'm actually looking at 12V pixels. Trying to figure out which type to buy.
1) Not exactly a maximum, but kindof there is. The more pixels you have on a string, the longer it will take the controller to be able to set all the pixels to the commanded color. When you set your pixels per string in the e682, it will show you how many times per second you will be able to change the string/s. My belief is absolute minimum should be 30 times per second. That gives you the same update rate as watching most videos on your PC. I am using 150 per string for ws2812 strips and ws2811 strings.
However, I have a few places where Im using more, like 180 per string.
If you have more than 50 per string you will probably have to powerinject. Try a string without power injecting and set all lights to full white. You will see the pixels at the end be a different color than the pixels at the beginning.
With 2811's on the 5V strings I have to inject every 50 pixels(including an injection at the very end of the string) to maintain full white. With 5V 2812 strips(150ish per string), Im not injecting at all, I can live with the discoloration. I just try not to use full white too much and not for very long so people dont notice. I have the strips on the house so I dont want a whole poopload of wires running around all over the place.
Also, another thing to keep in mind, you can buy the pixel strings made with thicker wires. Costs more, weighs more, but makes a huge difference in how much you have to power inject. If you are buying the pixels from China off of EBay then just send a message to the seller asking how much for thicker wires etc... I wish I knew that before I bought 8000 pixels. I spent a massive amount of time hooking up power injection wires. Very annoying.
Im using the first 12 ports at 150/string/strip and the last 4 for the weird sized ones or DMX in some cases.
Just a note, I wanted to give everyone a heads up on this forum, but havent got around to posting it.. If you using most of your ports on the E682, do NOT use the test patterns! It will screw you up, some of your strings/ports will be flashy and do weird things after you have some certain amount enabled. Just use your sequencer to set everything full white.
Also, if you using some ports as DMX, it appears to make quite a bit of noise on neighboring strings. I havent had time to get to the bottom of that problem, but for now Im keeping the DMX ports as far away from the pixels as possible(the wires also).
1) What is the maximum number of pixels that can be on a string? I have a string of 300, but can it also be 600, 900, etc? Like in a single string that might outline a house eve.
The maximum would be 2040 on one string. But I do not see anyplace that would be practical. Power injection and speed would be a limiting factor.
2) Is using one connector, with a 240 pixel string on 2-1, the same as using 60 pixel strings on 2-1, 2-2, 2-3 and 2-4? I mean, is there anything to be gained or lost by either method. In Vixen 3, for instance, a single string can be programmed as multiple strings, just by which pixels you define for which strings. So the question about connector use, popped up.
The connector on the board is rated for 4 amps. That is about 80 12 volt 2811 pixels.
3) Null pixels. If someone uses a null pixel, I would assume you still have to count it, as part of the string, even though you never intend to turn it on. Correct? And you would have to account for it in all your programming software, like declaring it a null-string and never assign a sequence effect to it. Correct?
As other have said you do not count the null pixel in your programing.
Last I checked the E682 configuration page will only allow you to put in up to "999" pixels per output. 2811's should be fine but GECE's have hardware limitations for how many can be in a string.
If using 12V 2811's be sure to watch what you buy, in 12V some of them group 3 pixels together, so they operate in groups of 3 not individual, where the 5V ones typically operate independent to each other. I am sure there are 12V ones that will operate independent, just be aware and ask to be sure that is what you are getting if you need individual control.
Yes, depending on type speed will slow down, but I find if you can keep above 20 fps it is all good, check your sequencing software for what it is really doing, like XLights is 20 fps so just need to stay at that or faster to be sure your hardware is capable of whatever your sequencer will do. Just realize the speed shown on the config page is a frequency, the more you put on a string the slower the update frequency gets, also this is just a theoretical calculated number, not an actual measurement, give yourself a bit of room for error.
On an E682 I find it is better to utilize more ports rather than try to put a lot on a few ports, 2040 pixels split over 16 outputs is around 127 per output, your built in fuse is now good for that number of pixels without having to add in additional fusing direct from the power supply (By the math it seems like too many but in reality works just fine). I find this is more of an issue when using an E6804 since you have 2040 pixels over 4 ports.
K-State Fan wrote:
The connector on the board is rated for 4 amps. That is about 80 12 volt 2811 pixels.
Where did you get this number? I don't see it posted in the E682 documentation. If true, this would by far be the limiting factor for most setups.
