Notifications
Clear all

E682 IP addr

20 Posts
5 Users
0 Reactions
7,422 Views
Posts: 1115
Topic starter
(@11bravo)
Noble Member
Joined: 14 years ago

Ok, scratch using the Laptop.
I went back and connected to the desktop PC since that is the computer that will be running the E682 in the show.
The desktop's address is 169.254.119.xx, So I had to change the E682 to address 169.254.119.xx to talk to it directly from the PC.
But that really isn't how I want to talk to it when the E682 is 300 feet from the PC.
So I changed the address to 192.168.1.xx to be compatible with the E1200 router that I will be using whose address is(192.168.1.xx)
I think I'm going to have to make that router DD-WRT though.
I believe that I will need two DD-WRT routers.
One connected to the PC and the other one connected to the E682.
That's my thinking anyway. And I think I got it going my way.
One router is already converted to DD-WRT, so I'll do the other one and see how it goes.


Reply
Electrified3
Posts: 716
(@electrified3)
Prominent Member
Joined: 13 years ago

What I typically do with a wireless set up on an E68x controller is put a router with DD-WRT in the controller enclosure and plug the controller into the router. If you are making it a "Bridge" then set it up on your existing wireless network and set your controller accordingly. (The DD_WRT has a good wiki step by step on configuring it for a bridge mode to an existing network) If you want it a separate network, configure it as a router and pick an IP range different than your existing networks to keep your show "isolated". You will just need a wireless adaptor in your PC to connect to the show router. Basically you will be configuring the router but not using the WAN connection, just setting it up to use the LAN and wireless connections to create a network without internet access.

If making it a separate network, configure the controller into that IP range, then set the router to that range as well when done. If using DHCP in the router be sure to disable/re-enable the PC network adaptor after the change or reboot the PC to reset the adaptor settings to the new network. If the PC is also connected to your home network, disable that until you have your show network configured and working as well.


Reply
Posts: 1115
Topic starter
(@11bravo)
Noble Member
Joined: 14 years ago
Electrified3 wrote:What I typically do with a wireless set up on an E68x controller is put a router with DD-WRT in the controller enclosure and plug the controller into the router. If you are making it a "Bridge" then set it up on your existing wireless network and set your controller accordingly. (The DD_WRT has a good wiki step by step on configuring it for a bridge mode to an existing network) If you want it a separate network, configure it as a router and pick an IP range different than your existing networks to keep your show "isolated". You will just need a wireless adaptor in your PC to connect to the show router. Basically you will be configuring the router but not using the WAN connection, just setting it up to use the LAN and wireless connections to create a network without internet access.

If making it a separate network, configure the controller into that IP range, then set the router to that range as well when done. If using DHCP in the router be sure to disable/re-enable the PC network adaptor after the change or reboot the PC to reset the adaptor settings to the new network. If the PC is also connected to your home network, disable that until you have your show network configured and working as well.

Thank you all for the replies,
Yes, that is what I'm working toward, to keep the show system off the home internet network. The old desktop doesn't have a wireless adapter. But I have two Linksys E1200's to use for getting data to the E682. One is converted to DD-WRT. (As I was using it in the home network to access the internet on that desktop.) I've change the address in it already to keep it separate from the home network. The other one I have not converted to DD-WRT yet.
But, I'm not too savey on what to change or set all the parameters to in the two routers to.


Reply
Posts: 1115
Topic starter
(@11bravo)
Noble Member
Joined: 14 years ago

Electrified3

Will look at these photos and tell me if there things that should changed in the settings.

http://doityourselfchristmas.com/forums/album.php?albumid=332


Reply
Electrified3
Posts: 716
(@electrified3)
Prominent Member
Joined: 13 years ago

Need a few more details to set it up, can you take screenshots of your primary router as well. We need to use that info in the bridge router to configure it.

As a note as well, if your existing home network is 192.168.1.xxx then you want to keep your other network out of that range, make all your devices, controllers, routers etc in a different subnet, like 192.168.10.xxx or whatever you want 10.10.10.xxx or anything, just not on the same subnet as your primary home network.

Here is the wiki on setting up the bridge as well, it is pretty good for explaining step by step what to do to set up the bridge as well. http://www.dd-wrt.com/wiki/index.php/Repeater_Bridge


Reply
Page 2 / 4
Share: