ok, I'll see what I can do on more screenshots.
Although, I have got something working. Both routers are converted to DD-WRT. One router is connected to PC and the other is connected to the E682, and I can get into the E682's web page wirelessly.
I have the router at the PC set to AP mode, and the router that is connected to the E682 is set to Client Bridge.
I tried changing the PC router to a different mode, but when I did, I could not access the web page in it.
I had to do a 30,30,30 reset to get back in to it.
My home network is 192.168.0.xx and the show network is 192.168.1.xx, so they are separated.
I am being able to run test on Pixels from xlights software. However I am getting some not so good results. Probably cause I don't have enough experience.
Since the show computer isn't on the internet now, I will have to save some screen shots on a USB stick and load them from the laptop.
Router info that is connected to E682
http://doityourselfchristmas.com/forums/album.php?albumid=335
Router info that is connected to PC
http://doityourselfchristmas.com/forums/album.php?albumid=332
Okay, a few things to try in the set up of your bridge router.
Setup-Basic Setup
Set Gateway to IP of PC Router "192.168.1.25"
Set Local DNS to IP of PC Router "192.168.1.25"
Disable NTP Client
Save
Services
Disable Dnsmasq
Save
Security -> Firewall
Uncheck all boxes...except Filter Multicast
Disable SPI firewall
APPLY Settings
It looks like you didn't set up any security encryption as well, might want to do that as well. I would get everything else working first and see where that gets you and see if the performance is what you are looking for, not sure if you were seeing lag or something in your previous set up. When you set up security encryption I would create it in the bridge first since you should be able to access it remotely, once you apply the change it will drop off until you change the PC router to match the security settings of the bridge. Once both match they should pick up again.
Ok, thanks, I will work on that today.
The test results I was talking about in previous post with xlights and pixels,
I connected the E682 directly to the PC and still got same results as I did when it was connected via routers.
I had 8 strings connected to outputs 1-1 to 2-4. (8 sockets) Some string colors are not what I selected them to be in xlights test. So bypassing the routers didn't help that problem.
11Bravo wrote:Ok, thanks, I will work on that today.The test results I was talking about in previous post with xlights and pixels,
I connected the E682 directly to the PC and still got same results as I did when it was connected via routers.
I had 8 strings connected to outputs 1-1 to 2-4. (8 sockets) Some string colors are not what I selected them to be in xlights test. So bypassing the routers didn't help that problem.
I would be looking at setup of your E682 or your setup in your XLights. Be sure in E682 all are setup the same, RGB, color order. If you test pattern 1 they should be red, 2 should be green, 3 should be blue. If not, write down the first letter of the color that shows up in test 1-2-3 and use the drop down to select the correct order. Also if each string is the same length, then use that as your pixel length for each group, say 50 pixels if they are 50 long each.
In Xlights, when you setup your E1.31, be sure to set channel length to 510 NOT 512, that will throw colours off on the pixels. Each pixel needs 3 channels, 170 x 3 =510 with 2 left over, you cannot use these 2 from one universe and 1 from the next, all 3 channels for the pixel must be in the same universe. So if using pixels on an E68x always set last ch at 510 not 512.
If you throw up a screenshot of your E682 setup and XLights setup can take a look.
