Controll DMX contro...
 
Notifications
Clear all

Controll DMX controller from E682

69 Posts
5 Users
0 Reactions
24.1 K Views
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
jerry72 wrote:I have 27 and 30 channel dmx controllers that use dip switches, I will have those connected to the e682 instead of using the dongle which is unreliable.

Gotcha. I just wondering if you try to set the 682 to 1 and see what happens. I'm not really familiar with DMX controllers but it seems like an addressing issue.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Is one of the dip switches used for test mode?

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

The only thing I can think of is the Cat5 hookup to the 682. It's possible the wire scheme isn't the same for your dmx controllers. One or several posts here show different color configurations for dmx.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Jerry72 posted this about the 682 and I'm not sure I understand it correctly. It appears the 682 using DMX is limited to 5 universes. Now, does that mean all outputs can not exceed 5 universes? If so then you have 6. Does the web page come up showing 682-5?
Here's what it says:
Operation: There are no new configuration commands with the E682. The E682 allows for 5 universes of E1.31 data, so the relevant lines of the configuration screen have been expanded to show the 5th universe, and the relevant configuration commands have been modified to allow the entry of addresses up to 5 universes. The default “as-shipped” configuration is now for 16 50-pixel strings, with a contiguous DMX address range beginning with slot#1 of the 1st universe. On the web page the E682 identifies itself as an “E682-5” with the -5 indicating the number of possible E1.31 universes. It is anticipated that this will be increased in future firmware releases since the new Ethernet hardware is capable of up to 8 universes. The web server is now on a dedicated Ethernet “socket” so there is no longer a conflict between the use of the 4th universe and the web browser as there was on the E681. Note: With the current firmware, updating of the web page will be slow when a test pattern is enabled. It is suggested that test patterns be disabled for greatest response speed when changing the board configuration via the web browser.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Angus40 posted a link to standard pinout for dmx in post 17. Not knowing if your DMX controller uses that standard pinout I would be hesitant telling you to use it. Since the 682 is low voltage it's possible itvwont hurt the DMX.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
pmiller wrote:Jerry72 posted this about the 682 and I'm not sure I understand it correctly. It appears the 682 using DMX is limited to 5 universes. Now, does that mean all outputs can not exceed 5 universes? If so then you have 6. Does the web page come up showing 682-5?
Here's what it says:
Operation: There are no new configuration commands with the E682. The E682 allows for 5 universes of E1.31 data, so the relevant lines of the configuration screen have been expanded to show the 5th universe, and the relevant configuration commands have been modified to allow the entry of addresses up to 5 universes. The default “as-shipped” configuration is now for 16 50-pixel strings, with a contiguous DMX address range beginning with slot#1 of the 1st universe. On the web page the E682 identifies itself as an “E682-5” with the -5 indicating the number of possible E1.31 universes. It is anticipated that this will be increased in future firmware releases since the new Ethernet hardware is capable of up to 8 universes. The web server is now on a dedicated Ethernet “socket” so there is no longer a conflict between the use of the 4th universe and the web browser as there was on the E681. Note: With the current firmware, updating of the web page will be slow when a test pattern is enabled. It is suggested that test patterns be disabled for greatest response speed when changing the board configuration via the web browser.

Sent from my SM-T710 using Tapatalk

This was for multicast


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

It didn't say that so it confused me. I'm easily confused.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

3:30 in the morning and I'm watching how caskets are made on How It's Made.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

With his dmx controllers he is good to go with native dmx setting and if e682 is configured for 4 * 170 pixel strings , 4 universes are available per cluster

Determining wire connections should be easy as Jim has documented XLR in the manual .


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
pmiller wrote:3:30 in the morning and I'm watching how caskets are made on How It's Made.

Sent from my SM-T710 using Tapatalk

Lmao 🙂

Reading the page up from balanced inputs in the e682 opman , multicast looks as though it may be a better choice for DMX.


Reply
Page 5 / 7
Share: