Controll DMX contro...
 
Notifications
Clear all

Controll DMX controller from E682

69 Posts
5 Users
0 Reactions
24.1 K Views
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

try setting the e682 to 170 pixels for each dmx stand and save .

then you can pair your start channels as you like .

each stand should be its own universe of 510 channels provided you set each stand to 170 pixels as described in the opman.


Reply
Posts: 357
Guest
Topic starter
(@jerry72)
Member
Joined: 13 years ago
angus40 wrote:try setting the e682 to 170 pixels for each dmx strand and save .

then you can pair your start channels as you like .

each strand should be its own universe of 510 channels provided you set each strand to 170 pixels as described in the opman .

These controllers control dumb nodes, not pixels. They use standard DMX firmware.


Reply
Posts: 357
Guest
Topic starter
(@jerry72)
Member
Joined: 13 years ago
pmiller wrote:FPP uses fseg files that you export from you sequencing software. You can't send data to FPP at the same time FPP is running. I sequence using Vixen. If I have FPP running at the same time the lights are all messed up. When Vixen is launched it automatically starts sending data to the controllers unless I turn off the controller output in Vixen.

Sent from my SM-T710 using Tapatalk

I am trying to use the test mode on FPP to test the lights, tried it from Xlights as well.


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

FPP needs to be set in bridge mode to test from your sequencing software.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 357
Guest
Topic starter
(@jerry72)
Member
Joined: 13 years ago

I got it figured out, i will have to daisy chain the two controllers instead of having them on separate outputs that way i dont have to change my the channel outputs on my sequences. You can only run 1 universe from a single output, you can not use the same universe on different outputs. Once i ran 510 channels off one output, i got them working. Have not tsted it in Xlights, but it is all good. Oh and i dont have to run Pi in bridge to test the E682, it is hooked to a router as is the pi.

E682

Reply
Posts: 357
Guest
Topic starter
(@jerry72)
Member
Joined: 13 years ago

Works off Xlights as well. I will just leave the pi like that, all my ESP modules will be accessed for testing through xlights.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
jerry72 wrote:I got it figured out, i will have to daisy chain the two controllers instead of having them on separate outputs that way i dont have to change my the channel outputs on my sequences. You can only run 1 universe from a single output, you can not use the same universe on different outputs. Once i ran 510 channels off one output, i got them working. Have not tsted it in Xlights, but it is all good. Oh and i dont have to run Pi in bridge to test the E682, it is hooked to a router as is the pi.

Way to go Jerry .

60 * atta boy's for your success and PMiller for sticking with it !

This was a good thread for my learning .

Thanks

Cheers


Reply
Posts: 357
Guest
Topic starter
(@jerry72)
Member
Joined: 13 years ago
angus40 wrote:Way to go Jerry .

60 * atta boy's for your success and PMiller for sticking with it !

This was a good thread for my learning .

Thanks

Cheers

What made me think of if was the DMX output on the Pi, it to has to be set at 510 channels, unlike the renard that can be set at whatever channel count ya have. This gets typed up and put in my binder.


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Well heck. It only took 2 days and 70 posts. 🙂
Ooops! Ever since November 15.

Sent from my SM-T710 using Tapatalk


Reply
Page 7 / 7
Share: