Controll DMX contro...
 
Notifications
Clear all

Controll DMX controller from E682

69 Posts
5 Users
0 Reactions
24.1 K Views
Posts: 357
Guest
Topic starter
(@jerry72)
Member
Joined: 13 years ago

Hopefully tonight I will have an answer as to how it all works. Because I am running esp modules, I switched over my pi to transmit multicast so I already switched the 682 to receive multicast.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
jerry72 wrote:Hopefully tonight I will have an answer as to how it all works. Because I am running esp modules, I switched over my pi to transmit multicast so I already switched the 682 to receive multicast.

Well , I hope you get success with resolving this today .

Remember that copper is still King !


Reply
Posts: 357
Guest
Topic starter
(@jerry72)
Member
Joined: 13 years ago
angus40 wrote:Well , I hope you get success with resolving this today .

Remember that copper is still King !

Well so far no success, the Green DMX light on the controller is blinking, which means the E682 is sending it DMX data, but can not turn on the lights at all. I have tried in unicast and multicast. I have changed the start channel for the controller on the 682 output page from 230 to 1 and back again. Changed setting in xlights and FPP, but still no joy on either tester.


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
jerry72 wrote:Well so far no success, the Green DMX light on the controller is blinking, which means the E682 is sending it DMX data, but can not turn on the lights at all. I have tried in unicast and multicast. I have changed the start channel for the controller on the 682 output page from 230 to 1 and back again. Changed setting in xlights and FPP, but still no joy on either tester.

Sounds like you need to email Jim at Sandevices.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Did you try and use the orange and brown wires for data and ground like it showed in a previous post?

Sent from my SM-T710 using Tapatalk


Reply
Posts: 357
Guest
Topic starter
(@jerry72)
Member
Joined: 13 years ago
pmiller wrote:Did you try and use the orange and brown wires for data and ground like it showed in a previous post?

Sent from my SM-T710 using Tapatalk

Yes, green light on the controller is blinking, so i am sure it is getting signal.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

How about the DMX controllers dip configurations , do that correlate with the e682 settings ?


Reply
Posts: 357
Guest
Topic starter
(@jerry72)
Member
Joined: 13 years ago

Here is my current setup, i have the dip switches set to channel 230 as well. I have tried putting the dip switch to channel 1 and the E682 to channel 1 but no joy. Tried giving the DMX there own universe as well, but still didn't work. I dont think this is an issue with the 682, again, green light is flashing on the controller. Tried running it all under unicast as well.

pi
E682
pi

Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

FPP isn't going to do much for you until you get the controller to output.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

FPP uses fseg files that you export from you sequencing software. You can't send data to FPP at the same time FPP is running. I sequence using Vixen. If I have FPP running at the same time the lights are all messed up. When Vixen is launched it automatically starts sending data to the controllers unless I turn off the controller output in Vixen.

Sent from my SM-T710 using Tapatalk


Reply
Page 6 / 7
Share: